First aid if the tachometer does not work on a VAZ 2107 with an injection and carburetor engine

Author: Ivan Baranov

The driver can learn about the main operating parameters of the vehicle thanks to the dashboard. This device is equipped with basic sensors and indicators that indicate the operation of certain devices. One such device is the tachometer. For what reasons does the tachometer on a VAZ 2107 carburetor not work and how to replace the device - detailed instructions are described below.

[Hide]

Why

The tachometer is not one of the “vital” devices of the “seven”, but its malfunction causes certain inconvenience. In addition, the situation when the VAZ 2107 tachometer jumps is a sign of problems in the ignition system or fuel supply to the engine. Therefore, at the first sign of a malfunctioning tachometer, you need to understand the causes of the breakdown and eliminate them immediately.

The connection diagram for the tachometer on a VAZ 2107 with a carburetor engine is slightly different from that used on models with an injector. But in general, the causes of the malfunction and the methods for eliminating them are similar.

Connecting a tachometer on carburetor and injection models

The connection diagram for the VAZ 2107 tachometer on an injection machine differs in that in this case the device reads data on engine speed not from the ignition coil, but from the engine ECU. In general, the connection procedure and operating principle are no different. The device has three terminals, two of which are connected to the “plus” from the ignition switch and “ground”, and to the third - a wire from the ignition coil or engine ECU.

Where to start troubleshooting

To troubleshoot, you will need a multimeter or “tester”. If the tachometer on a VAZ 2107 (injector) does not work, you should first look to see if the “Check Engine” warning light is on. If this is the case, then you can find out the cause of the breakdown by reading the error code from the controller. If the lamp does not light, you can skip this point.

Next, on the injection and carburetor models, you should check the condition of the electrical wiring going to the tachometer. The insulation of the wires must not be damaged, the tachometer must have good contact with ground, power and terminal “K” of the ignition coil or the engine ECU output. In addition, there may be a break or poor contact inside the device itself. In this case, it will have to be replaced.

If everything is in order with the wires and contacts, the problem is in the Hall sensor (on the injection “seven”), the ignition or fuel supply system.

Checking the ignition system

The VAZ 2107 tachometer circuit is the same for all models, the only difference is where it gets the data from. In the carburetor “seven”, information about engine speed is read from the ignition coil: every two spark discharges on the spark plugs is one engine revolution.

The tachometer may malfunction if the insulation of high-voltage wires is broken or the ignition coil is faulty. In this case, interruptions in engine operation and “floating” speed are also possible. In addition to the wires and coil, it is necessary to check the condition and adjustment of the breaker contact and the capacitance of the capacitor on it.

Faulty wires and, as a result, unstable engine operation, cause the tachometer to “jump” on injection VAZ models.

Hall Sensor

The tachometer on the VAZ 2107 (injector) reads information about engine speed from the computer. The latter, in turn, receives data from the Hall sensor. Poor contact at the sensor terminals or its malfunction leads to interruptions in engine operation and fluctuations in the tachometer needle. If the contacts can be cleaned, the sensor itself cannot be repaired. It is designed in such a way that the possibility of its repair is excluded. The faulty sensor must be replaced with a new one.

Fuel system malfunction

The cause of interruptions in engine operation and jumps in the tachometer needle can be either low-quality fuel or problems in the injection system. On carburetor models, disassemble the carburetor and clean the jets.

Most often, a “jumping” tachometer is the result of a clogged idle jet. The VAZ 2107 tachometer (injector) can “jump” if there are problems in the injection system. In this case, it is necessary to flush the injectors.

To check and clean the injection system, you need a special stand and equipment. It is better to entrust such work to service station specialists.

Malfunction of the gas distribution mechanism

When the tachometer needle begins to “jump” at high speeds, the problem may be associated with a malfunctioning gas distribution mechanism. In this case, it is necessary to check the tension of the timing belt connecting the crankshaft to the camshaft.

In addition, the speed may “float” due to a malfunction of the engine itself. Here it is worth checking the compression in the cylinders or contacting an auto mechanic.

If you delay diagnosis and repair, serious damage to the piston system may occur, which will require expensive complex repairs.

Source: https://semerkavaz.ru/ehlektrooborudovanie/pochemu-prygaet-strelka-takhometra-vaz-2107/

Symptoms of a problem

The reason for the tachometer failure can only be hidden in a power failure in the electrical circuit. The malfunction can be identified by the following signs:

1. The arrow jumps or does not function at all. The reason may be a disruption or break in the electrical circuit, a short circuit, or poor contact at the battery terminals.
2. The power unit operates with severe interruptions. A common reason is poor performance of the ignition coil, distributor, or capacitor. There may be a malfunction in the fuel injection system or the ignition timing is incorrect.
3. The power characteristic is broken.
4. The engine runs erratically or stalls when shifting into gear. Also, the reason lies in the electrical circuit or in the fuel supply system.

All these indicators mainly indicate a short circuit in the circuit or improper operation of the ignition system.

VAZ 2107 tachometer does not work

: 27.08.2018
When choosing a future profession or wanting to change their field of activity, thoughtful people study the market, assessing which ones are the most in demand, highly paid and prestigious.

After all, the right choice can significantly help in your career, which means it will allow you to provide yourself and your loved ones with a decent life, go here Honda.

Another thing is that the most prestigious professions require extraordinary qualities, hard work, perseverance and talent, but this game is worth the candle. Selecting a charger. Tips for use

In Russia, these professions began to appear on similar lists not so long ago, but over the past few years they have only been moving forward, and have now reached the highest position. Programmers of all stripes and types, designers, developers, web analysts, SEO specialists - this list can be continued for a very long time. BSZ problem with tachometer

One thing is clear - specialties related to computers and the Internet today are really in demand and quite highly paid. The lower bar may not impress beginners, but by achieving success in your chosen profession, you can increase your income almost indefinitely. Tachometer connection

articles: Top management Lawyers Logistics Medicine Accountant Auditor Information technology Sales promotion Management Purchasing manager Sales manager Beauty industry Creative activities Conclusion

The average person spends a third of their life at work, go here Honda. Highly paid specialist - more than half. Therefore, the desire to find a business for ourselves that will justify such a significant personal investment is quite natural for us. When choosing, you should take into account not only material remuneration, but also the correspondence of the chosen specialty to your personal calling: highly paid professions for girls are found in any industry - from medicine to design.

It is almost impossible to identify areas of activity in which women cannot work. The fair sex realizes itself with equal success in management, economics, IT and oil production. At the same time, there are a number of profitable professions for girls related to the beauty industry, the service sector or the same accounting department, where there are very few or no men.

Hello everyone, today I would like to talk about the possible reasons why the tachometer on a VAZ 2107 does not work. The tachometer on a car plays a very important role and therefore cannot be delayed and urgently repaired or, in extreme cases, replaced.

So, to begin with, you must understand that the VAZ 2107 has two types of engines, namely carburetor and injection. Accordingly, the tachometer connection diagram on these machines is different. Well, let's first look at the carburetor seven.

Tachometer on a VAZ 2107 carburetor engine

On the carburetor seven, three wires come out from the tachometer. Two wires are plus and minus (power) and the third wire is connected to the ignition coil. If the tachometer is out of order, then in order to understand the reason you need to get to the terminals that go to the tachometer and disconnect it.

THIS IS INTERESTING: Is it necessary to change the pump when replacing the timing belt?

You will need three wires to connect the tachometer directly to the battery plus and minus, as well as to the ignition coil, terminal K. Then you need to start the engine and see if the tachometer does not work, then the fault must be looked for in the ignition system or in the tachometer itself.

But, if the tachometer works, then the problem is in the wiring that goes to the tachometer.

Tachometer on a VAZ 2107 injection engine

Above we looked at tachometer malfunctions on the carburetor seven, now it’s time for the injection one. On the injection seven, there are no longer three, but four wires going to the tachometer. The two wires are plus and minus, the plus comes from the ignition switch, and the minus goes to the ground of the car. The third wire goes to the input of the control unit. The fourth is connected to the crankshaft position sensor. The best option to determine the malfunction of the tachometer on the injection seven is diagnostics. In this case, using the error codes, you can determine the reason why the tachometer does not work. Well, without diagnostics you can only check the contacts on the blocks. It also happens that the tachometer needle starts to twitch, this is mainly due to the fact that the owners change the standard wiring to a more modern one. And given the fact that the resistance is different, such a nuisance appears. Well, that’s all for today, we have looked at the main reasons for the failure of the tachometer on the VAZ 2107 for now. January 21, 2021 753

Source: https://bmw-history.ru/content/ne/2011275236-ne-rabotaet-tahometr-vaz-2107.html

Part selection rules

An important device for cars

You can install this unit yourself. To do this you will need the following tools and materials:

• screwdrivers,
• wiring diagram,
• keys,
• insulating tape,
• wires.

First you need to find out the operating principle of the unit in question. The pulses read by this device enter the ignition system coil, displaying information on the screen. Auto mechanics recommend buying an electronic tachometer. When choosing this device, you should take into account the structural features of the VAZ 2105. Otherwise, the tachometer will show revolutions with a slight error. You can install a universal unit with switches. To do this, connect it to any type of engine.

In the selection process, you should also take into account the fact that there are dial and electronic tachometers. You can install a tachometer on a VAZ 2105 of the first type with a tuner. The second type includes the Balsat TX-319t model. It is a microprocessor device, the main task of which is to monitor the operation of the “five” engine. If necessary, the driver can select the most suitable mode. Before you figure out how to install a tachometer on a VAZ 2105, you need to take into account the capabilities of the car:

1. measurement of crankshaft revolutions of 2-6 and 8-cylinder engines,
2. availability of watches,
3. ability to remember maximum and minimum temperatures,
4. presence of a stopwatch,
5. ability to measure crankshaft acceleration.

Installing an electronic tachometer involves independently adjusting the backlight. The advantages of the Balsat TX-319t among auto mechanics include the presence of a standby mode. This feature significantly reduces energy costs.

How to connect a tachometer of this type is of interest to many VAZ 2105 car owners. First, select a mounting location. The negative wire is then connected to the vehicle body. The plus wire is connected to the corresponding ignition terminal. A voltage of 12 W appears in it.

The backlight allows you to see the speed at any time of the day, so auto mechanics recommend installing just such units. Before starting work, you need to figure out how to connect a tachometer of this type. For this, an appropriate scheme is used. The backlight wires are connected to the side marker switch. If the car is of an injection type, then the device is connected to the controller of the electronic engine control system. In this case, reading is performed from the last element. Installing a tachometer from another vehicle is prohibited, as difficulties may arise in the operation of the mounted unit.

What does the tachometer on the VAZ 2107 work from?

This material will be somewhat philosophical, as we will try to understand why the VAZ 2107 tachometer jumps and its needle behaves inappropriately. Even if the quality of the engine does not change, there is still a feeling that something is wrong, the car is broken.

The sight of an arrow jumping from side to side is somehow very annoying. What to do, how to get rid of this? Of course, there will be some features if you have an injector installed.

However, even if there is a carburetor in the power system, the design of the tachometer turns out to be similar.

Why does the tachometer jump on a VAZ 2107?

If you are a little familiar with classic or contactless ignition systems, then you know that in them the tachometer is connected to the “K” terminal of the coil, or to a switch. This is where the impulse appears, which is necessary for the correct operation of the device. The speedometer is driven by a cable (if we are talking about a carburetor).

If you have an injector in the fuel system, then first of all look to see if the “Check Engine” warning light is on. If yes, then you need to do diagnostics to determine the exact malfunction. If not, then the diagnosis will not bring any results.

This step is relevant if you have an injector and a carburetor. Carefully inspect all electrical wiring, not only those parts that relate to the device, but also those lying nearby. The main thing is that there is no damage to the insulation, as this can lead to a short circuit.

Using a multimeter, check if there is ground on the tachometer. Very often, poor-quality contact becomes the reason why the VAZ 2107 tachometer jumps. Of course, if there is no minus in the entire dashboard, then you will not have a car, but a New Year’s garland - all electrical appliances will begin to turn on and off at their own discretion.

Ignition system

As mentioned earlier, the ignition system of the VAZ 2107 car and the tachometer needle are interconnected; they cannot exist without each other. And if the arrow twitches, and all the above tips did not help, you should pay attention to the condition of the ignition elements. First of all, inspect the wires for damage or lack of contacts.

Source: https://avtotop.info/ot-chego-rabotaet-tahometr-na-vaz-2107/

DIY replacement instructions

Car owners, as a rule, think about the need to service and repair the tachometer if it fails.

More information about replacing the device:

1. Disconnect the battery and use a flat-head screwdriver to pry and remove the three handles installed on the heater control selector.
2. Unscrew the nut securing the odometer reset lever, and also remove the washer installed behind it.
3. Next, using the same flat-tip screwdriver, pry off the cap of the bolt that secures the tidy. After removing it, unscrew the screw securing the shield to the center console bracket.
4. Having done this, move the right part of the tidy to the maximum, then remove the left part. After this you will have access to the back of the shield, now you need to unscrew the speedometer cable nut and completely disconnect it. Next, disconnect all hoses and connectors connected to the shield.
5. Remove the dashboard. Remove the tachometer from it and install a new one. If you have connected everything correctly, the installed device will work.

Photo gallery “Dismantling the tidy”

1. Unscrew the instrument mounting bolts.

2. Unscrew the nut securing the speedometer cable.

3. Disconnect the connectors from the device and remove it.
Loading …

Revs float on VAZ 2115

18 Oct
Failures in the fuel supply system and incorrect settings of computer engine control systems are the most common problems in modern cars. Thousands of drivers encounter such problems once a day at stations, but millions more operate cars with excessive fuel consumption and other problems, without even realizing that their car has a serious breakdown.

The very first and most important indicator of such a problem is uneven speed. If your car's idle speed fluctuates, you can be sure that it consumes 15-20 percent more fuel than what is written in the passport. If you notice such a problem, you should contact a professional service and have all the problems removed.

The most common causes of floating speed in a car

Diesel engines very rarely suffer from this problem. Floating speed in a diesel unit may indicate a breakdown of the injection pump system and other expensive and complex components. In carburetor gasoline power units, floating speeds indicate a bad carburetor setting or a breakdown of the electrical idle speed sensors.

More often, this problem appears in injection power units. And the most common reasons for unstable speed in a gasoline injection engine are the following:

• clogging of the jets through which fuel enters the chamber;
• a problem with the “brains” of the car - the computer that controls all engine functions;
• breakdown of the air flow sensor and excessive enrichment of the consistency;
• failure of the spark plug or high-voltage wire;
• faulty electronic wiring of the motor, lack of power to the sensors.

Revs float on VAZ 2115

The more expensive your car, the more technological mysteries it contains, which can cause floating speed. We consider the quiet and measured operation of a modern car unit to be an advantage. But from time to time, behind this silence and comfort, you can miss a serious problem, which leads to the need to change expensive car components.

Once you have noticed floating speed at idle, be sure to contact a specialist and remove all possible causes of this phenomenon.

Checking the operation of sensors in a car engine

As the idle speed begins to show inconsistent data, a number of sensors should be checked. Do more ordinary tasks before work. Check the integrity and serviceability of spark plugs and wires. The most common method is to pull out the wires one by one while the engine is running. This makes it possible to find which candle is not working and perform the necessary actions to replace it.

THIS IS INTERESTING: At what distance from the bus stop can you park your car?

If the spark plugs are working normally, it's time to look at the sensors:

• the main culprit for unstable speed is the idle speed sensor - it is checked by measuring the resistance in working and non-working states;
• The throttle opening sensor also causes such problems from time to time - you can check it visually while the engine is warming up;
• The mass flow sensor (mass fuel flow sensor) also often becomes the culprit of floating speed; it is inspected with the ignition on and the engine off by measuring the voltage at the contacts (should be about 1 Volt);
• The EGR (exhaust gas recirculation) sensor, if present, should also be checked and cleaned.

You can get more complete information on checking sensors from the video below

After testing all the sensors and checking their functionality, you should start the car again, warm it up one hundred percent to working condition and look at the tachometer needle. If the speed is still floating, you should contact the experts. It will be impossible to solve this problem without the help of others; you need professional equipment.

Let's sum it up

By checking sensors and controllers, you can gain reliable knowledge about the condition of your car, as well as about possible problems even before their real consequences. If the problem with uneven revolutions has not been identified, the reason may be in the computer, in a violation of the program, or in a wiring breakdown in a place unknown to you. On carburetor engines, the cause of such failures may also be a Hall sensor, which is not recommended to be disassembled without the help of others.

Be sure to adjust the speed of your engine, because this affects not only the convenience of travel, but also the efficiency of operating the car. With the help of impeccable engine operation, good consumption is achieved, a smooth increase in speed and no risk of excessive or very rapid wear of the unit.

Source: https://autoruservis.ru/plavajut-oboroty-na-vaz-2115/

VAZ 2107 tachometer jumps: causes and consequences

This material will be somewhat philosophical, as we will try to understand why the VAZ 2107 tachometer jumps and its needle behaves inappropriately. Even if the quality of the engine does not change, there is still a feeling that something is wrong, the car is broken.

The sight of an arrow jumping from side to side is somehow very annoying. What to do, how to get rid of this? Of course, there will be some features if you have an injector installed.

However, even if there is a carburetor in the power system, the design of the tachometer turns out to be similar.