We connect the tachometer 2106 to the injector. The tachometer WORKS!

Tachometer malfunctions

Despite the fact that the TX-193 tachometer is considered quite reliable, it also has malfunctions. Their signs are:

• lack of response of the needle to changes in engine speed;
• chaotic movement of the arrow up and down, regardless of the engine operating mode;
• obvious underestimation or overestimation of readings.

What kind of breakdowns do the listed signs indicate?

The arrow does not respond to measuring the number of revolutions

Usually, the lack of response from the arrow is due to a broken contact in the connectors of the main wires of its connection, or damage to the wiring of the circuit. The first step is:

1. Inspect the fastening of the conductor in brown insulation to terminal “K” on the ignition coil. If you detect poor contact, traces of oxidation, burning of a wire or terminal, fix the problem by cleaning the problem areas, treating them with anti-corrosion liquid, and tightening the fastening nut.
2. Check the reliability of the connection of the black and white wire to the vehicle ground. If contact is broken, clean the wire and the surface to which it is attached.
3. Using a tester, determine whether voltage is supplied to the red wire when the ignition is on. If there is no voltage, check the serviceability of fuse F-9, which is responsible for the integrity of the instrument panel circuit, as well as the condition of the ignition switch contacts.
4. Disassemble the instrument panel and check the connections of the contacts in the tachometer wiring harness block. “Ring” all the wires going to the device with a tester.

Video: tachometer needle does not respond to engine speed

The tachometer needle jumps chaotically

Jumps in the TX-193 needle in most cases are also a symptom of malfunctions associated with its electrical circuit. The reasons for this behavior of the device may be:

• lack of good contact at the negative terminal of the battery;
• oxidation or burning of the brown wire on the ignition coil;
• burning or wear of the contacts of the ignition distributor cap or slider;
• wear of the distributor shaft bearing;
• shorting the red wire powering the device to vehicle ground;
• malfunction of the crankshaft position sensor (for injection engines).

A similar problem is solved by stripping the contacts, replacing the ignition distributor cap, slider, support bearing, restoring the integrity of the insulation of the device’s supply wire, and replacing the crankshaft sensor.

Video: tachometer needle jumps

The tachometer underestimates or overestimates the readings

If the device is outright lying, then the problem most likely lies in the ignition system. In other words, it shows correctly, but the number of pulses created by the chopper per revolution of the distributor shaft is more or less than four. If the tachometer readings are incorrect, there is usually a deterioration in engine performance. In this case, the speed may fluctuate, misfires periodically appear, which is accompanied by engine vibration and white or bluish exhaust.

In this case, the fault should be looked for in the breaker, or rather, in its contact group or capacitor. To fix this problem you need to:

1. Disassemble the ignition distributor.
2. Check the condition of the breaker contacts.
3. Clean contacts.
4. Adjust the gaps between the contacts.
5. Check the serviceability of the capacitor installed in the breaker.
6. Check the serviceability of the crankshaft position sensor. In case of malfunction, replace it.

However, the reason may be in the tachometer itself. Malfunctions occur related to the parts of the electronic board, as well as to the milliammeter winding. You can't do without knowledge of electronics here.

Incompatibility of the TX-193 tachometer with a contactless ignition system

Older models of TX-193 devices are designed exclusively for contact ignition systems. All owners of “sixes” who independently converted their cars to a contactless system subsequently encountered problems with the tachometer. It's all about the different forms of electrical impulses arriving at the device from the breaker (in a contact system) and the switch (in a contactless system). The simplest way to solve this problem is to install a capacitor in the cut of the same brown wire coming from the breaker. But here it is necessary to experimentally select the desired container. Otherwise, the tachometer will lie. So, if you have no desire to engage in such experiments, just buy a device for a contactless ignition system.

Why does the VAZ tachometer jump?

It often happens that the needle starts to twitch. If the car is fuel-injected, then troubleshooting involves connecting a diagnostic scanner and checking the engine systems. Jumps in the TX-193 needle in most cases are also a symptom of malfunctions associated with its electrical circuit. The reasons for this behavior of the device may be:

1. lack of good contact at the negative terminal of the battery;
2. oxidation or burning of the brown wire on the ignition coil;
3. burning or wear of the contacts of the ignition distributor cap or slider;
4. wear of the distributor shaft bearing;
5. shorting the red wire powering the device to vehicle ground;
6. malfunction of the crankshaft position sensor (for injection engines).

A similar problem is solved by stripping the contacts, replacing the ignition distributor cap, slider, support bearing, restoring the integrity of the insulation of the device’s supply wire, and replacing the crankshaft sensor.

Another jump may be due to the inoperability of the capacitor located at the bottom of the breaker. The capacitor may be broken or its contact is very weak.

Tachometer malfunctions - finding the cause yourself

First aid if the tachometer does not work on a VAZ 2107 with an injection and carburetor engine.
It is better to take measurements with a multimeter. To operate, you must know how to use it. The “tester” makes it possible to measure power, “ground” and “ring” the main wire for a break.

Power measurements are carried out in DC mode (select a range within 20 Volts). In this case, “-” is always present, “+” appears after the ignition is activated. Ideally, the signal wire shows pulses while the crankshaft is rotating.

Breaks are looked for by setting the ohmmeter function on the multimeter. If the problem is in the contacts, move the harness/connector.

Is the tachometer not working properly? Sometimes this is due to design defects in the car. For example, it happens like this: the operation of a generator, when the current on the excitation winding is regulated by alternating voltage, is accompanied by “vibration” of the needle (typical of old VAZ cars). This defect can be corrected by changing the connection diagram or updating the dashboard.

Varieties

Tachometers produced on the market differ from each other in design and method:

• installations and connections;
• operating principle.

Also, special devices are produced for injection and carburetor engines - they are not interchangeable. For the VAZ-2105, a remote device is usually selected, since there is no room for a standard one in the panel of this car.

There are also non-contact varieties of tachometers. They don't need any connection at all. You just need to understand that these devices are used rather as diagnostic equipment that helps check the engine and adjust it. That is, they are not used in the mode of permanent recording of readings.

For those wishing to install a standard device, we recommend that you first replace the original dashboard with the one designed for the VAZ-2107 model. This shield has a socket, which means installing a tachometer on the 2105 will not cause any difficulties.

The remote type is placed in any convenient place - it comes with a special support leg. Instead, it is permissible to use double-sided tape. The cheapest option is the standard ones.

Installation on a car with a carburetor

Why the instrument panel of the VAZ-2115 does not work: repair

Before connecting the tachometer, it must be installed in the location chosen for it. This way you can immediately see how long of wire you will need. Then the negative cable is connected to ground. It is, as previously reported, black and white or completely charcoal.

Connect the brown or red wire to the ignition switch contact. Look at the diagram where the positive from the battery comes. If it is not there, then find it using a tester. This is done like this:

• set the multimeter to 20 V;
• Place the black probe on ground;
• Touch all the contacts in red one by one - the one you are looking for will have 12 volts.

The last posting is used to obtain data on the number of crankshaft revolutions 2105. Its color is not defined, each manufacturer uses its own. This cable in the contact ignition system goes to the distributor breaker. Otherwise, it is connected directly to the voltage switch. If the tachometer has its own backlight, then it is additionally connected to the car’s side lights circuit.

If the tachometer on a VAZ does not work

Usually, the lack of response from the arrow is due to a broken contact in the connectors of the main wires of its connection, or damage to the wiring of the circuit. The first step is:

• Inspect the fastening of the conductor in brown insulation to terminal “K” on the ignition coil. If you detect poor contact, traces of oxidation, burning of a wire or terminal, fix the problem by cleaning the problem areas, treating them with anti-corrosion liquid, and tightening the fastening nut.
• Check the reliability of the connection of the black and white wire to the vehicle ground. If contact is broken, clean the wire and the surface to which it is attached.
• Using a tester, determine whether voltage is supplied to the red wire when the ignition is on. If there is no voltage, check the serviceability of fuse F-9, which is responsible for the integrity of the instrument panel circuit, as well as the condition of the ignition switch contacts.
• Disassemble the instrument panel and check the connections of the contacts in the tachometer wiring harness block. “Ring” all the wires going to the device with a tester.

The first car of the Zhiguli family equipped with a tachometer was the VAZ-2103. “Kopeyka” and “deuce” do not have such a function, although they existed without problems and still exist today. For what purpose did the designers decide to equip the panel with it?

How a tachometer works: principle, device

Why the speedometer does not work on VAZ 2110, 2111, 2112

The “six” TX-193 includes:

• body in the form of a cylinder made of plastic with a glass holder;
• a scale divided into areas with dangerous/safe modes;
• backlight lamp;
• printed circuit board;
• milliammeter with a fixed pointer on the shaft.

The structure of the TX-193 tachometer is based on electromechanics. Its operation was established by measuring the number of electric current pulses in the initial (low-voltage) circuit of the VAZ-2106 ignition circuit. An important point is that in the “six” engine, for one rotation of the distributor shaft, corresponding to 2 crankshaft revolutions, the contacts in the breaker close and open exactly 4 times. These pulses are removed by the device from the final output of the initial winding of the electrical device, that is, the ignition coil. Moving through the elements of the electronic board, their sinusoid-like appearance changes to a rectangular one with a constant amplitude. So, the voltage goes from the board to the mA winding (milliammeter), and depending on the frequency of the pulses, it decreases or increases. The device cursor reacts precisely to these changes. Thus, the higher the current strength, accordingly, the more significantly the arrow moves to the right and vice versa.

Taking into account the fact that the VAZ-2106 has carburetor and injection engines, the tachometer connection is different. Let's talk about both variations.

Tachometer VAZ 2106

The first car from the Zhiguli family equipped with a tachometer was the VAZ 2103. Neither the “kopek” nor the “two” had such a device, but they drove and drive without it to this day without any problems. Why did the designers need to install it on the panel?

Purpose of the tachometer

The tachometer is used to measure the crankshaft speed. Essentially, it is a revolution counter, showing the number of revolutions to the driver by deflecting the scale needle to a certain angle. With its help, the person sitting behind the wheel sees in what mode the car’s power unit is operating, and also whether there is any excess load on it. Based on the information received, it is easier for the driver to select the correct gear. In addition, the tachometer is indispensable when adjusting the carburetor. It is its indicators that are taken into account when adjusting the idle speed and the quality of the fuel mixture.

What tachometer is installed on the VAZ 2106

“Sixes” were equipped with the same tachometer as “threes”. It was a TX-193 model. Precision, reliability and excellent sporty design have made it a kind of standard automotive device. It is not surprising that today many car owners install these tachometers as additional devices. Moreover, they are equipped with motorcycle and even boat engines. As for the Zhiguli, the device can be installed without modifications on such VAZ models as 2103, 21032, 2121.

Table: main technical characteristics of the TX-193 tachometer

TX-193 is still on sale today. The cost of a new device, depending on the manufacturer, varies between 890–1200 rubles. A used tachometer of this model will cost half as much.

Design and principle of operation of the TX-193 tachometer

The “six” tachometer consists of:

• plastic cylindrical body with glass holder;
• a scale divided into zones of safe and dangerous modes;
• backlight lamps;
• a milliammeter with an arrow attached to its shaft;
• electronic printed circuit board.

The design of the TX-193 tachometer is electromechanical. The principle of its operation is based on measuring the number of electric current pulses in the primary (low-voltage) circuit of the car’s ignition system. In the VAZ 2106 engine, for one revolution of the distributor shaft, corresponding to two rotations of the crankshaft, the contacts in the breaker close and open exactly four times. These pulses are removed by the device from the final terminal of the primary winding of the ignition coil. Passing through the parts of the electronic board, their shape is converted from sinusoidal to rectangular, having a constant amplitude. From the board, the current flows to the winding of the milliammeter, where, depending on the pulse repetition rate, it increases or decreases. The arrow of the device reacts precisely to these changes. The greater the current, the more the arrow deviates to the right and vice versa.

Electrical diagram for connecting the tachometer VAZ 2106

Considering that the VAZ 2106 was produced with both carburetor and injection engines, the tachometer connection was different. Let's consider both options.

Connecting a tachometer in carburetor VAZ 2106

The electrical circuit of the speed counter of the carburetor “six” is quite simple. The device itself has three main connection wires:

• to the positive terminal of the battery through the contact group of the ignition switch (red);
• to the “ground” of the car (white wire with a black stripe);
• to terminal “K” on the ignition coil connected to the breaker (brown).

There are also additional wires. They serve for:

• supplying voltage to the backlight (white);
• connections to the battery charge indicator relay (black);
• contact with the oil pressure sensor device (gray with a black stripe).

The wires can be connected either using a block or separately, depending on the year of manufacture of the device and its manufacturer.

In carburetor “sixes” with contactless ignition, the tachometer connection diagram is similar, except that the “K” terminal of the coil is connected not to the breaker, but to contact “1” of the switch.

Connecting a tachometer in injection VAZ 2106

In the VAZ 2106, equipped with engines with distributed injection, the connection diagram is slightly different. There is no breaker, no switch, no ignition coil. The device receives fully processed data from the electronic engine control unit (ECU). The latter, in turn, reads information about the number of crankshaft revolutions from a special sensor. Here the tachometer is connected to the power circuit through the ignition switch, the vehicle ground, the computer and the crankshaft position sensor.

Types of tachometers

Analog instruments use an induction magnetic coil, thanks to which the number of crankshaft revolutions is shown by an arrow moving along the scale. This device is installed as standard on most machines. It is almost the same size as the speedometer and is located next to it on the dashboard. This arrangement of the device is convenient for the driver, since it is always in front of the eyes and makes it possible not to be distracted from the situation on the road.

In digital devices, information is reflected on a liquid crystal or diode display. The number of revolutions is transmitted either by a magnetic sensor that records the passage of a specific point on the crankshaft near the measuring device. An electronic sensor – optocoupler – can be installed. It generates a beam of light and determines the rotation frequency by its reflection from nearby objects. The digital device is useful when tuning engines and operations with electronic ignition units.

Connecting tachometer 2106 to the electrical system

You will learn how to connect the tachometer 2106 correctly. This is one of the most important elements with which the operation of an internal combustion engine is monitored. For beginners, it provides a huge service, since starting up a hill must be done at a certain speed (this is taught in driving schools, and experienced drivers give very useful advice to beginners). For the first time, tachometers began to be installed on VAZ 2103 cars, the predecessor of the famous “Six”.

How does a tachometer work?

Now we need to look at the design of what the tachometer 2106 consists of. How to connect it correctly will be discussed in the next chapter of our article. The device is of an electromechanical type, which means that its circuit is combined - the pointer is driven using pulses. The VAZ 2106 tachometer reads pulses that occur in the ignition system.

The internal combustion engine operates in such a way that during one revolution of the crankshaft in the distributor, the contact group opens and closes four times. From here you can see the logic - the device needs to count the total number of pulses and divide by four. Perhaps this will be enough to understand the principle of operation of the device. Now it’s worth talking about what the 2106 tachometer circuit looks like and considering its connection to the ignition system.

How is the tachometer connected?

There are several wires, with the help of them the normal functioning of the device is carried out. A thick red wire connects to the ignition switch. Namely, with the contact on which voltage appears when the key is turned. The white wire is connected to the power supply circuit for the instrument panel lighting.

Don’t get confused, inspect the wires carefully, as there is also a white one with a black stripe. It connects to the "mass". The brown wire is connected to the ignition coil - to the “K+” terminal. It is this contact that reads the pulses. The black wire is connected to the generator voltage regulator.

The gray wire with a black stripe connects to the oil pressure sensor. If you decide to install a VAZ 2106 tachometer for a penny, for example, then you need to take into account that the device has several more warning lights. Whether you use them or not is up to you. If there is a need only to control the speed, then you only need three wires - to connect to ground, the ignition switch and the coil.

If the tachometer 2106 does not work, then disassembling it is almost pointless. Only a complete replacement can help. It is unlikely that you will be able to find a break in the head that moves the arrow. But a violation of the integrity of the tachometer connection wires can be detected.

Frequent tachometer breakdowns

If the VAZ 2106 tachometer needle jumps, look for a fault in the capacitor. It is located at the bottom of the distributor. The capacitor is either broken or the contact is weak. If there is mechanical damage to the tachometer, it will be easier to replace it with a new one. It is worth noting that the needle sometimes jumps at high speeds. Most often, the cause of this behavior is a bad battery.

If there are problems with the device, then you will need to know how the VAZ 2106 tachometer circuit is designed, because you will have to carry out diagnostics. Disconnect the wire from the coil and turn on the ignition. If there are no problems, then the arrow will be at zero. But if there is a short circuit to the body, the arrow will deflect to the maximum value. If it begins to slowly return to zero, then we can conclude that there is a malfunction in the distributor capacitor.

Please note that the VAZ 2106 tachometer can be installed on injection engines, but a small upgrade will be required. The fact is that the device reads pulses from the coil, and in injection engines the tachometer operates using the crankshaft speed sensor

Therefore, a completely different sensor element is needed. Replacing the head from the injection seven is ideal. True, replacement work must be carried out as carefully as possible so as not to damage the device.

Video: Connecting the VAZ 2106 Tachometer to the Injector

What tachometer is installed on the VAZ 2106

The sixties were equipped with the same tachometer as the three. It was model TX-193. Precision, reliability and good sporty design have made it a typical standard car device. It's not mind-blowing that many tachometers now install these tachometers as additional tools. Moreover, they are equipped with motorcycle and even boat engines. As for the Lada, the device can be installed without any configuration on such VAZ models as 2103, 21032, 2121.

Table: main technical properties of the TX-193 tachometer

TX-193 is on sale now. The price of a new device, depending on the manufacturer, ranges from 890 to 1200 rubles. A used tachometer of this model will cost half as much.

Design and principle of operation of the tachometer TX-193

The “six” tachometer consists of:

The design of the tachometer TX-193 is electromechanical. The principle of its operation is based on measuring the number of electronic current pulses in the primary (low-voltage) circuit of the car’s ignition system. In the VAZ 2106 engine, for one revolution of the camshaft, which corresponds to two revolutions of the crankshaft, the contacts in the switch close and open exactly four times. These pulses are removed by the device from the final output of the primary winding of the ignition coil. Passing through the parts of the electrical board, their shape changes from a sinusoidal shape to a rectangular shape with a constant amplitude. From the board, the current flows into the winding of the milliammeter, where, depending on the pulse frequency, it increases or decreases. The device's needle responds precisely to these configurations. The greater the current, the more the arrow deviates to the right and vice versa.

VAZ 2106 tachometer connection diagram

Due to the fact that the VAZ 2106 was produced with both carburetor and injection engines, the connection of the tachometer to them was different. Let's look at both options.

Connecting a tachometer to a VAZ 2106 carburetor

The electronic circuit of the rotating carburetor "six" counter is quite ordinary. The device itself has three main connecting wires:

There are also additional wires. They are used for:

The wires can be connected either by the device or separately, depending on the year of manufacture of the device and its carburetor with contactless ignition, the tachometer connection diagram is similar, except that the “K” output of the coil is connected not to the switch, but to contact “1” of the switch.

Connecting a tachometer to the injection system of a VAZ 2106

In the VAZ 2106, equipped with engines with distributed injection, the connection diagram is slightly different. No switch, no switch, no ignition coil. The device receives fully processed data from the electrical engine control unit (ECU). The latter, in turn, reads information about the number of crankshaft revolutions from a special sensor. Here the tachometer is connected to the power circuit through the ignition switch, vehicle ground, computer and crankshaft position sensor.

Tachometer malfunctions

Although the TX-193 tachometer is considered to be quite reliable, it also has faults. Their signs:

What defects do these signs indicate?

The arrow does not respond to measuring revolutions

Typically, the lack of response to the arrow occurs due to poor contact in the connectors of the main wires of its connection or damage to the wiring. 1st thing to do:

Video: tachometer needle does not correspond to engine speed

The tachometer needle jumps randomly

Jumping TX-193 arrows are almost always also a sign of defects related to its electronic circuitry. The reasons for such behavior of the device may be:

This problem can be solved by opening the contacts, replacing the ignition distributor cap, slider, stubborn bearing, restoring the integrity of the insulation of the device's power supply, and replacing the crankshaft sensor.

Video: tachometer needle jumps

Tachometer underestimates or overestimates

If the device is open, the problem is most likely related to the ignition system. In other words, this only correctly indicates the number of pulses generated by the chopper per revolution of the camshaft, more or less than 4. If the tachometer readings are incorrect, engine performance is usually worsened. At the same time, the rotation can float, and sometimes shots occur, accompanied by the engine stopping and a snow-white or grayish exhaust.

In this case, the fault should be found in the switch or, more precisely, in its contact group or capacitor. To fix this problem, you must:

But the reason may be in the tachometer itself. Problems with parts of an electrical board, also with the winding of a milliammeter. You can't do this without knowledge of electronics.

Incompatibility of the TX-193 tachometer with a contactless ignition system

Older models of TX-193 devices are intended only for contact ignition systems. All owners of “sixties” cars, who independently turned their cars into a contactless system, encountered problems with the tachometer. Things in various forms of electronic pulses arrive at the device from the shredder (in a contact system) and the switch (in a contactless system). The easiest way to solve this problem. install the capacitor in a section of the same brown wire coming from the switch. But here you need experience to choose the right container. Otherwise, the tachometer will lie down. So, if you do not want to carry out such experiments, just buy a device for a contactless ignition system.

Replacing the carburetor with a system with distributed fuel injection

Carburetor cars are gradually disappearing from our lives; such cars are no longer produced by industry, and their design is considered obsolete. But the question of whether a carburetor injector is better or not is still relevant; debates on this topic are often held on automobile forums.

Each type of fuel system (FS) has its own advantages and disadvantages; the injector is a modern unit that provides a more accurate dosage of the air-fuel mixture. But the carburetor circuit is simple, it is easier to diagnose, and often not only specialists, but also many drivers can deal with the problem.

Connection diagram for tachometer to motorcycle

The diagram for connecting a tachometer to a motorcycle is not fundamentally different from its installation on a VAZ-2106 car. The input of the device is connected to the output of the primary winding of the coil, after which the positive and negative wires are connected to the battery. Installing the toggle switch on the positive line will significantly save battery power when the motorcycle is idle.

A two-cylinder unit with single-channel ignition must be equipped with a rectifier. The battery that powers the tachometer is connected to its output. When the TX-193 is directly connected to the generator, the device will fail in the shortest possible time.

In the case of dual-channel ignition, to transmit pulses from both cylinders it is necessary to create an identical tachometer input line. After drilling an additional hole in the bottom, connect the wire to the device terminal.

Three-cylinder motorcycles are usually equipped with three-channel ignition systems. In this case, the connection to the tachometer is made from any two coils. In the same way, pulses are supplied in multi-cylinder equipment, but here it is more advisable to use models designed for this type of engine.

Connecting a tachometer to a single-cylinder unit is a little more complicated. Here it is necessary to adjust the resistor R7, which is responsible for the sensitivity of the measuring device. If necessary (lack of power), you should double the power of capacitor C5, and then readjust the resistor.

If the device does not work or does not work correctly

Since generators of foreign engines are usually more powerful, you should measure the battery charge current with an ammeter or a combined instrument and make sure that it does not significantly exceed 0.

Two wires are power supply plus and minus, and the third is connected to terminal K of the ignition coil. The relay is installed in the engine compartment, on the right side.

Unfortunately, the ignition pulses produced by this Magdino turned out to be weak and did not ensure normal operation of the tachometer. This device can be installed on cars with both a contact ignition system and a contactless one. But if there is a short circuit to the body, the arrow will deflect to the maximum value.

The greatest difficulties await owners of single-cylinder engines. In order to find out what caused the failure, you need to get to the back of the instrument cluster and disconnect the terminals from the block that goes to the tachometer. If the previous steps did not allow you to identify and fix the problem, it probably lies in the ignition system itself.

Read additionally: Frequency of measuring the resistance of grounding devices PUE

Popular materials

It can be used to measure the rotation speed of any engine that has electronic or contact ignition. Almost everywhere they write that these tachometers may not be suitable for a contactless ignition system; they will lie or show starting from the rpm, that the circuit will need to be re-soldered.

Connect a white wire with a black stripe to the negative. Frequent tachometer breakdowns If the VAZ tachometer needle jumps, look for a fault in the capacitor. Consequently, for one revolution of the roller, four current pulses are created in the primary circuit of the ignition system and two voltage pulses are created for one revolution of the crankshaft.

How to choose the right tachometer for your car

There is no place for a tachometer in the panel, so it will have to be placed somewhere on top. This problem is most easily solved for two-cylinder two-stroke outboard engines equipped with an electric starter and battery and having a single-channel electronic ignition system with a two-spark ignition coil. The most rational use of a thyristor voltage regulator with parallel connection of thyristors.

Otherwise, you risk being left without a device. As for digital devices, they are more reliable in terms of operation, but the weak points in such devices are the board with the processor, as well as the signal counter. Accordingly, the tachometer connection diagram for a carburetor or injector is combined - the tachometer needle on a VAZ is set in motion using impulses. Therefore, the dashboard from the VAZ will do without major alterations. Of course, many people have become tired of it, but it is precisely on it that radio amateurs make various designs. Tachometer for VAZ 2101. How to install a tachometer for VAZ 2101.

Tachometer VAZ 2106: types, connections, possible malfunctions

The “Sixes” were equipped with a tachometer model TX-193. This tachometer consists of:

• plastic cylindrical body with glass holder;
• a scale divided into zones of safe and dangerous modes;
• backlight lamps;
• a milliammeter with an arrow attached to its shaft;
• electronic printed circuit board.

The principle of its operation is based on measuring the number of electric current pulses in the primary (low-voltage) circuit of the car’s ignition system. In the VAZ 2106 engine, for one revolution of the distributor shaft, corresponding to two rotations of the crankshaft, the contacts in the breaker close and open exactly four times.

These pulses are removed by the device from the final terminal of the primary winding of the ignition coil. Passing through the parts of the electronic board, their shape is converted from sinusoidal to rectangular, having a constant amplitude. From the board, the current flows to the winding of the milliammeter, where, depending on the pulse repetition rate, it increases or decreases. The arrow of the device reacts precisely to these changes. The greater the current, the more the arrow deviates to the right and vice versa.

Connecting a tachometer in carburetor VAZ 2106

Electric circuit of the speed counter of the carburetor “six”

In a contactless ignition system, the tachometer is connected not to the coil, but to the switch

Connecting a tachometer in injection VAZs

It should be taken into account that the colors of the wires and their purpose may differ depending on the manufacturer of the device, but for the standard “TX-193” device, which is usually used in “sixes”, the diagram is as follows:

• A white cable is required to connect the backlight.
• The red wire is connected to the ignition switch, a fuse is used for this, this cable supplies power when the ignition is activated.
• A white cable with a black break is required for connection to the car body.
• The brown wire connects to terminal K on the coil.
• The black wire is connected to the charging current indicator relay. The latter, in turn, is installed on the right in the engine compartment.
• The gray-black cable is required to connect to the engine fluid pressure regulator installed to the left of the engine.

Let us immediately note that the fuel supply system – injector or carburetor – does not play a special role here. As you know, currently the most common are cars with the following engine types: gasoline or diesel. Depending on this, the tachometer is selected, unless, of course, it comes in the stock version.

The thing is that on gasoline engines the tachometer reads data from the ignition coil, or rather, the impulses that arise here. However, the design of diesel power plants does not provide for this unit. Accordingly, here the tachometer reads pulses not from the ignition coil (for lack of one), but from the generator.

The first two wires (12-volt and Signal) are to contacts “B” and “K” of the ignition coil, respectively. All that remains is to secure the mass in any convenient place.

1. tachometer VAZ;
2. trip computer;
3. ECM;
4. crankshaft position sensor;
5. ignition module.

Domestic 2106 models were equipped with the same tachometer as the VAZ-2103. The sample was designated TX-193. Stability, clarity, excellent sporty style made it, in some way, an ideal automotive device. Such devices, which is not at all surprising, are now installed by many car owners in the form of auxiliary devices.

The electrical circuit of the rotation counter of carburetor VAZs is quite simple. The device itself has three main connection wires:

• directed to the “ ” terminal of the battery through the contact link of the ignition switch (color red);
• to the mass of the vehicle (white wiring with a black stripe);
• to terminal “K”, which is on the ignition coil, combined with the breaker (color brown).

In addition, there are auxiliary wires that are intended for the following purposes:

• supplying current to the backlight lamp (white);
• linking with battery indicator relay (black);
• contact with the oil pressure regulator (color gray with a black stripe).

The wires are connected using the connector or separately. This is influenced by the year of manufacture of the device and its manufacturer. In turn, in a VAZ-2106 car (carburetor), which has non-contact ignition, the tachometer connection diagram itself is identical. An exception is when pin “K” is combined with contact “1” of the switch, and not with the breaker.

In “sixes” equipped with engines with distributed injection, the connection will be slightly different. There is no switch, no ignition coil, and no breaker. According to the scheme, the device receives fully processed information from the ECU (electric engine control unit). It is the latter that reads data regarding the number of crankshaft rotations from a special sensor.

The principle of its operation is based on measuring the number of electric current pulses in the primary (low-voltage) circuit of the car’s ignition system. In the VAZ 2106 engine, for one revolution of the distributor shaft, corresponding to two rotations of the crankshaft, the contacts in the breaker close and open exactly four times.

These pulses are removed by the device from the final terminal of the primary winding of the ignition coil. Passing through the parts of the electronic board, their shape is converted from sinusoidal to rectangular, having a constant amplitude. From the board, the current flows to the winding of the milliammeter, where, depending on the pulse repetition rate, it increases or decreases.

The arrow of the device reacts precisely to these changes. The greater the current, the more the arrow deviates to the right and vice versa.

• In a contactless ignition system, the tachometer is connected not to the coil, but to the switch
• Connecting a tachometer in injection VAZs
• It should be taken into account that the colors of the wires and their purpose may differ depending on the manufacturer of the device, but for the standard “TX-193” device, which is usually used in “sixes”, the diagram is as follows:

Cars October 22, 2017

A VAZ-2106 tachometer is used to control the engine crankshaft speed. The indicator is installed in the dashboard, to the right of the speedometer.

AvtoVAZ did not produce cars of the sixth model with injection engines; only in the last years of production a small batch rolled off the IZH-Avto assembly line.

Therefore, the tachometer was only used with ignition systems that are compatible with carburetor injection.

Many motorists do not use a tachometer - it is not as important as the speedometer (which is used to control speed, so as not to violate traffic rules and not earn a fine). Using a tachometer, the engine speed is measured - and this sometimes turns out to be useful for beginners who have not learned to “feel” the engine’s operation.

When carrying out tuning, beautiful devices are installed that improve the appearance of the dashboard. The sixes had four-cylinder engines.

They have one feature - for each revolution of the ignition distributor shaft (distributor), four closures of the breaker contact group occur. With its help, the impulse necessary to form a spark is created.

In a contactless system, the functions of a mechanical breaker are performed by a Hall sensor.

The VAZ-2106 tachometer circuit depends on which ignition system is used on the car. In the case of a contact system, connections are made as follows:

1. The left terminal of the tachometer (red) is connected to the positive of the ignition switch. This is the power supply to the device - it is supplied only when the ignition is on.
2. The middle wire (white with a black stripe) is connected to the ground (body) of the car.
3. The right terminal of the tachometer is a signal terminal; it is painted brown. It is connected to terminal “K” of the ignition coil and the contact group of the distributor.

Read more: Replacing the VAZ 2106 camshaft, which one to choose, how to install instructions with photos and videos
Connecting the tachometer to the elements of the electronic ignition system is very similar:

1. The red wire connects to the ignition switch. Power is supplied, as in the previous version, only when the ignition is turned on.
2. The negative wire (white with a black stripe) is connected to the car body.
3. The control wire (brown) is connected to terminal “K” of the coil and contact “1” of the electronic switch.

In both cases, the power wire for an incandescent lamp is connected to the tachometer, which is necessary to illuminate the scale.

In general, connecting the VAZ-2106 tachometer will not cause any difficulties - it has only three main wires, the rest are auxiliary. The TX-193 device model can be used both in VAZ-2106 cars and in similar models. It can be used to measure the rotation speed of any engine that has electronic or contact ignition.

Using a tachometer, the number of pulses in the primary ignition circuit is measured. On four-cylinder four-stroke engines, for one revolution of the distributor shaft, 4 closings and openings of the contact group occur.

In other words, each revolution initiates the formation of 4 pulses. But for each revolution of the crankshaft, only two impulses are generated.

Consequently, there is a direct relationship between the rotor speeds of the distributor and the crankshaft.

The design of the device contains not only a speed indicator, but also an oil pressure lamp.

Before connecting the tachometer to the VAZ-2106, you need to familiarize yourself with the purpose of all the wires:

1. White - intended for connection to the part of the wiring through which voltage is supplied to illuminate devices.
2. The red wire and fuse provide power to the device. Moreover, voltage is supplied to it only when the ignition is turned on.
3. White with a black stripe – connection to vehicle ground.
4. Brown is the signal wire through which voltage pulses are received from the coil.
5. Black – designed to connect the electromagnetic relay of the charging current indicator. The relay is installed in the engine compartment, on the right side.
6. The gray wire with a black stripe connects to the oil pressure sensor on the engine block.

Characteristics of the tachometer on the VAZ 2106, instructions for connecting it yourself

How does it work?

To understand how the VAZ 2106 plug-in household or car tachometer works, you need to understand what the design of the device is. In accordance with the tachometer diagram, this device belongs to electromechanical type devices. Accordingly, the tachometer connection diagram for a carburetor or injector is combined - the tachometer needle on a VAZ 2106 is driven by impulses. The device itself reads signals that arise during the operation of the ignition system.

The power unit of domestic “classics” operates in such a way that during one revolution of the crankshaft, the contact group of the ignition breaker must close and open 4 times. Accordingly, here you can already understand how the tachometer on a VAZ 2105 or 2106 works - the device needs to count the total number of signals and divide the resulting value by 4.

Six tachometer connection diagram

Where is?

There may be several options for the location of the device; the main requirement in this case is convenience for the motorist. If the VAZ 2106 tachometer is connected at home, then it is usually placed on the dashboard or on the center console, in fact, as in production. Of course, if necessary, you can install the device in any convenient place, but the two options listed above are the most convenient.

Before installing and connecting the tachometer, you need to take into account that the readings shown by the device should always be in sight. While driving, the driver must not be distracted from the road. A digital device can be installed on the “six”, although initially these models were equipped with analog devices.

Possible faults

Why doesn’t the tachometer work, why does the needle on the installed device twitch and jump, how can I check the device myself? We suggest that you familiarize yourself with the list of the most common malfunctions for the device. If you notice that the arrow on the supplied device begins to twitch, then most likely the jump may be due to the inoperability of the capacitor located at the bottom of the breaker. The capacitor may be broken or its contact is very weak. If you notice that there are signs of damage on the device itself, then it would be best to change it (author - Master Ruslan channel).

In some cases, the needle jumps due to the use of a battery that has expired. One of the most common causes of device failure is wear of the cable; in some cases, the problem may occur due to the failure of the coil, but this happens much less frequently. If you are using an analog device, it may not work correctly due to any damage to the microboard. As for digital devices, they are more reliable in terms of operation, but the weak points in such devices are the board with the processor, as well as the signal counter.

Diagnostics can be done as follows:

1. Disconnect the wiring supplying the device.
2. Turn the key in the ignition.
3. If the needle of the device is at 0, this indicates its performance. If the arrow tends to the maximum value, most likely the problem is a short circuit. If the needle very slowly returns to 0, then most likely the reason lies in the breaker capacitor.

Connection features

So that you can understand how the device should be connected, you first need to become familiar with what these or other wires are intended for.

It should be taken into account that the colors of the wires and their purpose may differ depending on the manufacturer of the device, but for the standard “TX-193” device, which is usually used in “sixes”, the diagram is as follows:

1. A white cable is required to connect the backlight.
2. The red wire is connected to the ignition switch, a fuse is used for this, this cable supplies power when the ignition is activated.
3. A white cable with a black break is required for connection to the car body.
4. The brown wire connects to the K+ terminal on the coil.
5. The black wire is connected to the charging current indicator relay. The latter, in turn, is installed on the right in the engine compartment.
6. The gray-black cable is required to connect to the engine fluid pressure regulator installed to the left of the engine.

Video “Tuning a six-wheel tachometer”

Detailed instructions for tuning the six-wheel device, as well as the entire dashboard, are presented in the video below (author - Auto VAZ channel).

Connecting the VAZ 2106 Tachometer to the Injector

The tachometer is used to measure engine speed only for carburetor cars. This is a device located on the front panel.

This cannot be called fundamental, but for a novice car owner who has not yet “heard” the engine of his own car, this helps to calculate the number of revolutions of the engine and crankshaft. This also plays an aesthetic role. Many car enthusiasts love to display modern devices on the control panel.

The VAZ 2106 has a four-stroke 4-cylinder engine, and during 1 revolution of the ignition distributor rotor, the contacts of the switch, the so-called distributor, open and close four times.

Other VAZ models have different engines, so you need to take this into account when installing tachometers. Pulse measurement is the basis of the tachometer and is dependent on the engine speed.

It is important to note: Any brand of car must have its own measuring device, otherwise the readings will be fake.

Mechanism design

On a plastic case with a glass holder there is a milliammeter of an ordinary traditional design with an attached scale. Zones of unsafe turns of the crankshaft are marked on it in different colors: the previous zone (5500-6000) is highlighted in yellowish color, and the zone of unsafe turns (more than 6000) is highlighted in reddish.

The device glows moderately with a lamp type AMN 12-3. At the bottom of the scale there are three color indicators that indicate respectively: charge volume, oil pressure and parking brake status. Inside the tachometer there is a moving coil with a permanent magnet, thanks to which the pulse indicator is driven.

The device is electric, so it works by igniting the car.

Connecting the tachometer VAZ 2106

When purchasing a new heart rate monitor, you need to add a note on connecting the device. You can also find installation diagrams in motorist manuals. But, if you are not an experienced mechanic and do not deal with electronics, contact the service department: for a small fee you will save your time.

In this video you will learn how to connect a tachometer! Enjoy watching.

And for those who want to self-medicate, the connection process diagram is quite simple:

These are the three main wires. Helpdesk for:

Most common device failures

The TX-193, with its non-removable design, is a complex electrical device, so it is virtually impossible to troubleshoot problems at home. Most likely, you will have to purchase a new device. In this video you will learn how to improve the tachometer of the VAZ 2106. We are watching!

If the tachometer does not work: make sure all the proper wires are connected correctly. We call the cable from the ignition coil and check the contact. You need to measure the current resistance.

Then check the “plus” and “minus” of the battery outputs and the circuit between the ignition module and the tachometer contact. Often a malfunction can be caused by replacing the “original” high-voltage wires with silicone ones. They have different linear resistance, and the pulse shape will change across the coil winding.

For a person with a certain technical ability, it will not be difficult to check the device's board. To do this, disassemble the case:

Car battery rating. You can find out which brands are included in this ranking on our website.

We recommend that you read this article to find out how to install a subwoofer in your car.

You can find out how much a Solex 21083 carburetor costs, here on our website you will also find unique material for this device.

It is recommended to repair the tachometer only at 100 or 100. Experienced and understanding craftsmen will be able to quickly identify damage and repair it. Otherwise, you risk being left without a device.

A device such as a tachometer does not affect the operation of the engine or the performance of the car, but without it, the dashboard of a modern car will be faulty. In this article we will look at why you need it, how it works, what obstacles it has and how to deal with them without the help of professionals.

Tachometer VAZ 2106

The first car of the Zhiguli family equipped with a tachometer was the VAZ 2103. Neither the “kopek” nor the “two” had such a device, but they drove without any problems and drove without it as before. Why did the designers need to install it on the panel?

Let's get started

• First, the cylinder head is removed and the entire ignition system is removed, as well as all the fuel pipes under the hood. The thermostat and generator are disconnected. Then, instead of the removed gas tank, a new injection tank is installed.
• Next, the cylinder head is removed and the carburetor with electrical wiring is dismantled - it will need to be replaced. The cooling system pipes are disconnected. Be careful not to allow liquid to come into contact with skin.
• Now the pan is disconnected and new injection pistons are installed instead of the old pistons. They have a higher compression ratio compared to carburetor engines. After this, a new oil pump and cooling system are installed. A place is being prepared for a new sixteen-valve head - to do this, you need to shorten the bolts of the old one, and, if necessary, drill holes in the new one.
• The fuel tank is installed in its place and connected to the new fuel lines. Wiring is connected from the control unit to the fuel pump. Next, a hole is created for the knock sensor assembly. The pump and breather for crankcase ventilation are being replaced.
• At the junction of the collectors and the head, the protrusions are removed, and after a previously installed new gasket, the head is mounted. After this, the thermostat is installed and the coolant hoses are connected. A belt is installed, as well as a generator with a drive. All sensors are replaced with new, injection ones.
• The valve cover is placed in place, the surface of which is pre-treated with sealant. The wiring is connected to the sensors, ignition switch and dashboard. Now a new exhaust system is being installed. Coolant. Fuel and oil are poured back into the system. You can check how the updated motor works.

This, of course, is not an exact instruction on how to change an injector to a carburetor, but only an algorithm of action. Because a lot will depend specifically on the brand of your car, and on which controller you will assemble the injector. But understanding the technical process will allow you to realize how much work you will have to face. As you can see, nothing is impossible.

Now you know how to convert a carburetor to an injector, and what is needed for this.

The injection method of supplying fuel to a car has a number of advantages over the traditional carburetor method. That is why many owners of older generation cars want to install an injector on their car instead of a carburetor. These are indeed quite sensible thoughts, but only if you are going to register everything correctly with the traffic police or will not drive onto public roads. The fact is that today cars cannot be converted independently; for each change in the technical base, you need to obtain permission from special organizations. But no one will give you permission to install injection injection on a carburetor engine. Therefore, you can immediately abandon this process if you are afraid of problems with traffic police officers while operating your car on public roads.

If you are not afraid of the registration procedure or problems with the traffic police, then you can achieve considerable benefits by installing simple injection equipment. It is enough to purchase a set of necessary parts, carry out the work, check the necessary settings and obtain the required quality of vehicle operation. Operating a vehicle will become much more convenient if you use modern fuel supply systems. There are several important advantages that the car driver receives in this case. However, all benefits are offset by the fact that this modification is not official and cannot be registered. Many lawyers can challenge this point, because the size and type of engine does not change. True, the number of horses changes, which determines the transport tax.