Idle speed regulator РХХ-60 405-406-409 engine

Purpose and principle of operation

This article describes the idle air control valve. Its structure, purpose, and operating principle are given. The design of the idle speed controller РХХ-60 is considered. The IAC malfunctions are described in detail. Describes how to check the idle air control. The sequence for replacing the idle air control valve is outlined.

The idle speed regulator РХХ-60 is a two-winding rotary solenoid with a slotted passage hole, the cross-section of which changes according to the program of the electronic control unit. The regulator is connected to the wiring harness using a three-pin socket with a latch.

The purpose of the IAC is to perform the following main functions:

• automatic engine start and warm-up at idle speed;
• stabilization of minimum idle speed;
• control of cyclic air filling at partial loads;
• damping of air flow during sudden opening and closing of the throttle valve.

The principle of operation of the idle air regulator is to regulate the cross-section of the idle air passage channel when an electrical signal acts on the wire winding of the idle air regulator.

An electric current is supplied from the electronic control unit (ECU) to the IAC stator winding, which, interacting with the constant magnetic field of the rotor, generates a control pulse of various duty cycles with a frequency of 125 Hz. In this case, the rotor together with the valve rotates at a given angle and changes the flow area of ​​the bypass channel, through which the intake air enters the throttle space, bypassing the throttle valve. As a result, the engine is supplied with air at idle speed with the throttle valve closed.

The degree of opening of the idle speed control varies from full opening (240 steps) when the engine is started to full closing in the EPH mode; at idle speed the regulator is open by approximately 85...100 steps (35...45%) for a warm engine.

The power supply to the electromagnetic windings of the idle speed regulator, РХХ-60 is carried out from the on-board network through the main relay, and the windings are turned on by connecting them to ground through the power channels of the control unit.

Malfunction of ignition system components

A malfunction of the ignition system makes it impossible to ignite the combustible mixture at the appropriate engine stroke. This manifests itself as regular misfires, disrupting the stability of its rotation. The revolutions float, when you press the accelerator they do not increase or increase with difficulty, the engine troits and may stall. All this is accompanied by thick exhaust smoke, which is uncharacteristic of normal fuel combustion.

The malfunction may be due to wear of spark plugs, armor wires, or ignition coils. Also, the reason may lie in incorrect setting of the ignition timing on engines with a distributor. All components of the system are subject to inspection and troubleshooting; after identifying a defective part, it must be replaced or adjusted.

Instability of internal combustion engine operation under various conditions can be caused by a number of reasons. This is why comprehensive diagnostics of equipment and components associated with the fuel-air system is required if the idle speed fluctuates.

Idle air control device

The idle air control, РХХ-60, consists of the following parts, shown at the top in the figure:

• Plug block - 1;
• O-ring - 2;
• Fastening washer - 3;
• Armature axis mounting flange - 4;
• Armature winding - 5;
• Rotary glass - 6;
• Magnet - 7;
• Housing - 8;
• Fixed anchor - 9;
• Armature axis - 10;
• Magnetic core - 11;
• Bearing retaining ring - 12;
• Ball bearing - 13;
• Bearing seal - 14;
• Inlet pipe - 15;
• Rotary valve - 16;
• Emphasis - 17;
• Roller bearing - 18;
• Damper shaft - 19;
• Output pipe - 20;
• The letter x indicates a permanent connection

Malfunctions of the idle speed controller РХХ-60

• The malfunction lamp lights up after turning on the ignition. Self-diagnosis of the unit records fault codes 161…166. Check the serviceability of the additional air regulator circuits 37e, 4, 26.

Fault codes for the idle air regulator РХХ-60 for the 409.10 engine with the Mikas 7.2 ECU

Decoding idle air control fault codes

Fault codes 161, 162, 163, 164, 165, 166 - malfunction of the additional air regulator control circuits. Possible causes of the malfunction: the regulator is not connected to the ECM wiring harness, a break in circuit 37 of the regulator power supply from the main relay, a break in ground wire 14 from the unit, a break or short circuit to ground/on board of the regulator control circuits (4, 26), a malfunction of the power channels of the regulator control ( block outputs: 4, 26), malfunction of the additional air regulator: short circuit of the regulator electromagnet windings (active resistance below 10 Ohms).

Fault codes for the idle speed regulator IAC, engine 40900A with ECU Mikas-11, UAZ 316300

Decoding IAC fault codes

Fault codes 1750-1755 - malfunction of the additional air regulator control circuits. Possible causes of the malfunction: the regulator is not connected to the ECM wiring harness, an open circuit 37 of the regulator power supply from the main relay, a break in ground wire 14 from the unit, an open or short circuit to ground/onboard of the regulator control circuits (4, 26), a malfunction of the power channels of the regulator control ( block outputs: 4, 26), malfunction of the additional air regulator: short circuit of the regulator electromagnet windings (active resistance below 10 Ohms).

Recommendations

Comments 26

Hello! solved a problem?

I changed it for a while and then it started to float again

I have the same thing, it worked fine for six months

I need to try to reflash it

Just the fuel pump or did you replace the entire assembly, along with the fuel sensor?

It came as a kit, pump, glass, level sensor, which by the way is lying

My sensor is also lying

It worked for me too, until I flashed it for Euro 2, a glitch in the factory firmware

When I start it cold, if you touch the pedal, the speed also fluctuates, if you don’t touch the pedal everything is fine...

We need to see what firmware it is. At 799 31 the factory glitch was with the speed floating when cold.

Looks like lambda umbrella 1 or 2. And so the idle regulator is responsible for idle. stroke or throttle sensor. Go for diagnostics, if necessary, ask the reprogrammed one, otherwise you can guess for a long time. And for the future, buy and install an on-board vehicle so as not to pay diagnosticians. Washing the throttle is unlikely to help because the revs are floating and not standing. Don’t worry, go to a diagnostician.

What onboard tool do you recommend to diagnose and remove errors? From operating experience

Every man to his own taste. Who likes what for the purpose of exploitation. The main thing is that the on-board vehicle is compatible with the brains of your car. I prefer the multitronic 580. But I use skat2. When I bought skat2 multitronic 580 they didn’t produce it. And so, in my opinion, they found a very good place for him in the place of the wind blower. But the main thing is that it produces errors. Many bortoviks have many settings: for example, setting on. and off cooling fan and many others. But there is one But! All this works with the native firmware, if you decide to reflash these settings may not work. What I mean by this is that there is no point in buying an expensive and very sophisticated on-board vehicle; I repeat, it is enough for the on-board engine to read the errors and reset them. And I personally encountered the above.

Read more: Change glass on A5

Everything they wrote is crap, I also have 405.24 E3. The problem with Mikas et11 is in the firmware, the chiptuner has freely available firmware, anyone who knows even a little can flash it. You can find more details on the gazelle forum, I changed mine and everything is OK. Good luck.

First, look at the weight of the engine, the pigtail on the intake manifold in the area of ​​cylinder 4, and then if that doesn’t help, look further.

Let's start in order 1. Check the spark plugs, or better yet replace them with new ones 2. It's better to replace the explosive wires with new ones too 3. We're looking for air leaks into the manifold past the mass air flow sensor

The MAF.is weird...try to start it without it.

We swam on the working Gazelle only in the morning, I pressed the gas a little and held it for 3 seconds, and then released it and everything leveled out! I have no such problems with Euro 3, I drove on different firmware now Euro 0 works fine, mixed consumption is 11.8 liters, highway 9.5 -10.5 liters

Check the pressure in the fuel rail both at idle and when throttled. It should be at least 2.8 when you press the gas pedal sharply, and so the edge is 3 atmospheres. It is possible that the springs inside the throttle assembly have stretched out (non-removable, replace only) look at what kind of error light is on. If pxx is limited in power and blocked. The culprit is the throttle assembly.

Checking the РХХ-60 for operability

• Connect terminal 2 IAC plus from the battery, and terminal 3 IAC minus. The IAC damper should open completely.
• Connect terminal 2 IAC plus from the battery, and terminal 1 IAC minus. The IAC damper must close completely.

Checking the idle air control regulator РХХ-60 using a Multimeter

1. Check the resistance of the IAC windings. Resistance between pins 1-2 and 2-3. Resistance should be 12±1Ohm
2. Check for a short circuit (breakdown) between the IAC windings and the IAC housing. Check for short circuit between pins 1, 2, 3 and the housing.
3. Measure the resistance between pin 1 and the body, between pin 2 and the body, between pin 3 and the body. It must be at least 1 MOhm.

Interchangeability of idle speed controllers РХХ-60

• Idle air regulator РХХ-60, catalog number MP-406-1147051-02, for engine 4213, 409 UAZ, 406 GAZ, MetalPart;
• Idle speed regulator РХХ-60, catalog number 406-1147051-02, for engine 4213, 409 UAZ, 406 GAZ, manufactured by PEGAS.
• Idle air regulator РХХ-60, catalog number 406.1147051-02, for engine 4213, 409 UAZ, 406 GAZ manufactured by UAZ, ORIGINAL.
• Idle air regulator РХХ-60, catalog number 406.1147051-02, for engine 4213, 409 UAZ, 406 GAZ manufactured by Cartronic.

Replacing the idle air regulator RXX-60

1. Remove the negative terminal from the battery. This must be done in order not to damage the electronic elements of the Electronic Control Unit (hereinafter referred to as ECU). They consume little current and are very sensitive to voltage drops and stray currents.
2. Disconnect the terminal block from the IAC. To do this, press the spring clip down and remove the terminal block.
3. Loosen the two clamps on the rubber tubes and remove the tubes.
4. Unscrew the two M6 bolts with a 10mm wrench and remove the IAC
5. Remove the IAC from the clamp
6. Place the rubber hose on the new IACs.
7. Place a metal clamp over the rubber tube on the IAC
8. Secure the IAC with two M6 bolts using a 10mm wrench to the engine receiver
9. Place two rubber pipes on the IAC tubular fittings and secure them with clamps
10. Connect the terminal block to the IAC.
11. Connect the minus terminal to the battery.

Basic faults

Despite the fact that the Gazelle is considered a durable truck, harsh operating conditions and poor fuel negatively affect the 405 engine for the Gazelle, as well as other elements of the vehicle. To ensure that Gazelle repairs or Sobol repairs do not have to be done constantly, you need to know the main faults of the car. Among the most vulnerable nodes are:

• chassis;
• engine
• body;
• fuel system.

Repair of “Sable” or “Gazelle” will be needed in the following cases:

• knocks and noises occur;
• power dropped sharply;
• oil pressure has decreased;
• consumption of fuel and other consumables has increased.

It should be noted that most of the signs can be heard when the ZMZ-405 engine is running. In extreme cases, the ZMZ-405 cylinder head will need to be replaced. To prevent major problems, you should periodically diagnose Gazelle faults. In most cases, identifying the cause of the malfunction and performing qualified repairs on Gazelle-Business can only be done in a specialized car service center.