Installation and connection of fog lights on Granta

But I encountered some minor difficulties. 1) Type of lamps.

I read the Internet, there are few posts on this topic, I found one - type h11.
I came to the store, just in case, I asked exactly how “a light bulb for PTF grants.” People ask me “what base?” Gru - “like H11.” The seller is not a fact! And he says that in addition to H11 there is another one. And the bulbs are non-returnable, so I had to figure out exactly which one. As a result, I found out that I have an H11 from a photograph from my blog post
, where the fog lights are visible on the removed bumper.

2) Price

. Here I must say that the cheapest H11 lamp in that store was hella for 410 rubles for 1 piece! Not cheap! Unpleasantly surprised. There are lamps for 700-800! (regular ones, it seems). I googled it and decided to take Hella. Should be normal. China did not decide, as there may be problems with poor light, excess current (melting wiring, connectors, or even worse). I bought it in general.

3) Replacing the lamp

. Again, there is not enough information, there is a video on YouTube where they chat about this topic... I came across a recording here on the drive, how someone on a grant changed the lamp in the PTF, so he even cut out a “hatch” in the standard fender liner! This method is not acceptable to me. I also didn’t want to remove the factory fender liner - I still have “fangs” (bumper body kits), which are secured with 2 screws from the factory fender liner... As a result, at the dacha, the idea came to me - to bend the bumper out of engagement with the fender, having first unscrewed 2 screws, connecting the bumper to the fender liner. Everything should be clear in the photo. In the end it took about 5 minutes to get the job done. Everything went smoothly. PTF works. I'm happy )

By the way, from the Lada Granta owner's manual

:
“To free access to the fog lamp from under the front wheel arch, you must first REMOVE the wheel and partially release the fastening of the front fender flap by REMOVING 6 SCREWS.
Bend the shield, remove the inoperative lamp...” In the standard Norm, Standard, Lux, Liftback configuration, fog lights (hereinafter referred to as PTF) are not installed in the front bumper. Instead of accessories, plastic plugs are built in. Let's look at how to install fog lights on a Granta liftback step by step below.

Preparatory stage (selection of PTF for Lada Granta)

The range of PTFs is not large; it is represented by several domestically produced models. Some owners claim that PTFs from Opel and Ford are compatible, but the information has not been verified.

OSRAM kit 21900-3743010

*prices are as of September 22, 2018.

Step-by-step process for preparing and installing fog lights

In the auto store we purchase: PTF, corrugation (at least 3.0 m), adapters - adapters for PTF with standard wiring.

• To remove the front bumper, unscrew three self-tapping screws on each side, four plastic clips, three “10” bolts in the lower perimeter;
• We remove the structure along with the radiator grille;

It is important to know. In the Norma and Standard models, there is no hole for adjusting the fog lights. The owners independently cut out a diameter of “8”. In the Liftback body modification, the opening is factory-made.

• We cut out the opening for the fog lights along the contour, it is factory-made;
• To make it smooth, treat the surface with a household hairdryer;
• We fix the headlights on three standard mounts;
• We connect adapters to each of the lamps, since the standard block with wires is short, its length is not enough;
• We put on the front bumper, screw it in with bolts and plastic clips.

Installation of PTF

The entire installation process is divided into two stages according to complexity:

1. Direct preparation of seats and securing PTFs in them;
2. Integration of electrical components into the standard wiring system.

Seating equipment

To carry out this operation you must:

• Remove the front bumper;
• Cut holes;
• Provide reliable fixation of lighting fixtures.

Advice! If the fog lights of the Lada Grant vibrate on uneven roads, they will blind oncoming drivers. Therefore, take care about their secure fixation. Also order the production of stickers for the headlights - this will help protect them from damage.

After dismantling the bumper, you need to install it on a flat surface. Then arm yourself with a sharp needle file and start cutting out holes.

As a result of this work, the edges of the holes will be uneven.

But it's not a problem:

• Take a small diameter sanding stone;
• Clamp it into a drill or cordless impact wrench;
• Carefully trim the edges of the holes.

The housings must now be installed into the prepared holes.

To do this, turn the bumper over and:

• Insert PTF;
• We combine the mounting holes with the fastening points;
• We fix them using self-tapping screws;
• We inspect from the front side the correct installation;
• If everything is in order, use a screwdriver to tighten the screws until they stop.

The photo shows the process of fixing PTF

Connection to electrical circuit

The instructions included in the installation kit prescribe the following connection procedure:

1. Insert incandescent lamps;
2. Fix the pads on the plinth;

1. Pull the wires from the headlights through the engine compartment into the car interior;
2. Install the relay and fuse into the mounting block;

1. Connect one of the wires to the rear PTF power button;
2. Install the bumper on the car;
3. Connect the battery and check that the fog lights are working correctly. (see also article)

Wiring diagram for fog lights Lada Granta liftback

Engine compartment

• We lay an additional wire from the right PTF headlight to the left one. We solder it and bring it into the engine compartment to connect to the relay.
• We fix the mass to the body at the place where the bumper is attached, maybe under the license plate, in the center.
• Do not forget to lay all electrical wiring in a corrugated material made of fireproof material.

Interior of the Lada Granta liftback car

• We lay the corrugated hose through the hole in the hydraulic corrector seal.
• The connection is best made at the ignition switch. That is, when turned off, the headlights will go out automatically.
• Open the glove box lid, press the side stops, and remove the lid.
• We stretch our hand into the cavity and carefully squeeze out the block of two buttons for controlling the heated glass and PTF.
• We power the minus from the heater button. Plus we won’t take it, since they will be activated at the same time.
• We connect the positive cable and install the unit again.
• We connect to the positive from the ignition switch unit (blue wire), it is located under the steering wheel.
• Finally, we power the relay - regulator: ground - wire from the button - end to the PTF - plus to the ignition.

In each specific configuration, the color scheme of the wire may differ. Read the diagram in the instruction manual for details. Classic colors: red, yellow, blue, brown. If you do not want to supply power through the ignition switch, the connection diagram is simplified with one less procedure.

How to install fog lights on a Lada Granta

The installation of Grant fogs involves several stages of work: the preparatory stage, the installation and connection stage. Fog lights are installed in the lower part of the car bumper in specially designated standard stamped places.

Preparatory work includes preparing the necessary tools and materials. For work we will need the necessary tools and components:

• a set of fog lights for Lada Granta, matching the characteristics;
• installation kit for connection;
• drill with a thin drill bit;
• emery stone, stationery knife, set of keys and wire cutters;
• flathead and Phillips screwdrivers, fine-grained sandpaper or file.

We also recommend reading the article on how to install DRLs (DRL, daytime running lights) on a car. From this article you will learn about what DRLs are, their features, why this element is needed, as well as how to choose and install daytime running lights on a car with your own hands.

Installation of Grant fogs:

• disconnect the negative terminal from the battery;
• unscrew the bolts securing the radiator grille and bumper, as well as the bolts located under the license plate;
• then unscrew the lower mounting bolts, the fastening screws of the bumper from below with the fender liners and in the wheel arches;
• pull out the bumper, carefully pushing its corners to the sides;
• place the bumper on a flat surface to prepare space for the headlights;
• carefully, so as not to damage the bumper, drill a hole around the perimeter of the stamped recess and get rid of the plugs using a knife;
• smooth the uneven edges of the hole with an emery stone or fine-grained sandpaper or a file clamped into a drill;
• insert the fog lamp housings into the seats and secure them with self-tapping screws;
• install the entire structure in place and begin connecting the foglights according to the connection diagram (with pulling the wires under the hood).

Please note that before snapping the edges onto the bumper wings during installation, you must connect the PTF to the new wiring. Next, you need to move on to the stage of how to connect fog lights to Granta.

To connect fog lights to Grant you will need:

• wiring, connection diagram;
• relay for “4” or “5” contacts with a capacity of 15A;
• external lighting control unit or on/off toggle switch.

General procedure for connecting fog lights to Grant:

• install a fuse and relay in the mounting block responsible for the fog lights;
• place the on/off toggle switch on the instrument panel console (if using a control unit, the toggle switch is installed to the left of the steering wheel in a vertical position);
• Connect the fog lights according to the connection diagram supplied with them.

All contacts must be well insulated and correctly connected according to the connection diagram. Having installed the fog lights, they also need to be adjusted. You can do this at a service station or yourself.

To self-adjust, you need to park the car at night at a distance of five meters from a wall or some other flat surface, then use a long Torx T20 screwdriver (headlights with convex glass) or a Phillips screwdriver (headlights with flat glass) to adjust the PTF.

Step-by-step instructions for installing a rear fog light

Many Lada Granta Liftback car owners are surprised to hear about this, but it is a fact. Of course, we are not talking about PTF in its classic form, but about a laser brake light. It is installed in the rear of the car and informs the driver behind about the vehicle. Since there is no strictly defined installation location, it is customary to fix it in the area of ​​the license plate, under the lower contour of the bumper, in the spoiler. There are known cases of embedding an accessory inside.

A bright red light beam informs drivers behind, preventing accidents. The brake light is also used when it is necessary to notify the driver of the need to switch the high beam headlights. An alternative way to use lighting when backing up or parking in conditions of limited visibility. The maximum effective beam length is 25.0 meters. Exceeding the length does not guarantee the quality of lighting.

The voltage is supplied from the left/right brake light. Activation is possible either by pressing the brake pedal or by a separate button. The owner makes the decision based on personal beliefs. In practice, activation occurs with an autonomous button, since when driving backwards it is not always advisable to use the standard brake pedal. It is strictly forbidden to point the laser beam at the windshield area behind the driving driver.

Reviews

Conclusion Every product has its own buyer. If you don’t find fault with a budget car, which is the Lada Granta Liftback, the quality of PTF lighting is good, it is enough for visibility. Of course, when compared with headlights from foreign brands in the premium segment, the advantage of the latter is obvious. In order to increase the service life of accessories, purchase products exclusively from certified points of sale. Require the provision of documents, check the functionality on site.

Fog lights

Fog lights for the Lada Granta are available with two types of glass:

• flat;
• convex.

Headlights with flat edges are produced by Bosch. Parts from a well-known company are considered quite strong and fit perfectly into standard seats.

Convex glass is manufactured at a factory in the city of Kirzhach. According to car enthusiasts, such glass is more susceptible to cracks due to mechanical stress and temperature changes. They are perfect for Grants, the dimensions and placement of the headlights are completely the same.

Connection diagram

The kit includes everything you need for connection, but you should stock up on electrical tape, a sharp knife, pliers, a screwdriver, a drill and a set of wrenches in advance.

Where can I install PTF

In the design of the modern Granta, the installation locations are precisely worked out: under the license plate, on the sides. Some bumpers even have recesses there . In any case, for proper installation, the front bumper of the car will have to be removed.

But before that, you should go shopping and find the necessary parts. Today's market offers both bumpers with recesses and bumpers with headlights already installed. The choice, as always, remains with the owner.

Most Lada Granta cars do not have fog lights, but there are recesses in the bumper for do-it-yourself installation

Instructions for installing headlights for dummies

The entire process of equipping a car with foglights can be divided into several stages:

1. Removing the bumper.
2. Installation of headlights.
3. Wiring.
4. Connecting headlights.
5. Reassemble the parts in reverse order.

Removing the front bumper

The Granta's bumper is integral with the radiator grille, so in order not to distort the latches under the wings, it is advisable to remove it together with a partner.

Photo gallery: necessary tools

• crosshead screwdriver;
• 10 mm wrench, 10 mm socket;
• 8 mm wrench;
• TORX T-20 wrench.

Bumper removal algorithm

1. Unscrew the front license plate.

To access the mounting bolts, remove the front license plate

With the hood open, find and unscrew the bolts securing the radiator grille

The next step is to unscrew one of the bolts and a pair of screws securing the bumper,

Unscrew a pair of screws on one and the other side of the bumper

Unscrew four screws in the wheel arches - a pair on each side

Video: step-by-step process of removing the front bumper

DIY headlight installation

For the Lada Granta, two types of headlights are offered today:

• Bosch - with flat glass;
• Kirzhach is convex glass.

Both headlights are standard, so their choice is up to the consumer.

What tool do you need?

In addition to headlights, to equip a car with PTF you must have:

• self-tapping screws (6 pieces for attaching headlights);
• drill;
• set of drills;
• countersink or sandpaper;
• stationery knife;
• sealant.

Experts recommend installing headlights in accordance with the following plan:

A hole with a diameter of up to 10 mm is drilled in the center of the oval for the headlight.

Make a 10mm hole in the center of the notch to start cutting

Starting from the center of the hole, carefully cut out a circle of the required size.

It is better to cut the hole in several steps so that your hand does not slip and damage the bumper.

After cutting the hole for the headlight, sand it down so that it does not extend beyond the outer diameter

Secure the headlight using self-tapping screws

After installing the headlight, coat all joints with sealant.

The last paragraph of the instructions is optional. However, experts recommend not to neglect it, otherwise dirt, snow or water may get into the cracks.

The steps described above are repeated in the same sequence to install the second headlight.

How to wire and connect a headlight

To connect the PTF you will need various tools:

• installation kit for connecting fog lights on Grant. It includes a button, a relay, wiring in the cabin, wiring under the hood;
• corrugation (for example, 9 mm for the interior and 16 mm for the hood);
• insulating tape;
• drill;
• set of drills;
• 10 mm head;
• 13 mm wrench.

An installation kit for connecting fog lights on a Grant will make the car owner’s work much easier

Replacing rear lights

The Granta taillight is mounted on 3 nuts, which are tightened from the trunk side. To dismantle the headlight you need:

1. Open the trunk lid.
2. Fold back the fabric cover.
3. Unscrew the 3 nuts with an 8 mm wrench.
4. Disconnect the plug with wiring.
5. Carefully remove the part from the groove.

All work on disassembling the bumper and removing the front and rear lights is carried out using ordinary wrenches, which are sold in most auto parts stores.

Self-installation of fog lights will save at least 3,000-5,000 rubles, which would have to be paid to a car service center.