How to install a rear window on a VAZ 2109 ~ AUTOTEXNIKA.RU

How to remove the windshield on a VAZ 2109, glass removal and installation

How to remove and install rear window

Removing the rear window is similar to the front fragment, only removing the rubber seal should begin not from the middle, but from the edges in the upper part. After the tape is pulled out along the top layer, the auto glass is removed in or out. The rear window is installed on a VAZ model 2109 using a rope or cord. Algorithm of actions:

The rope is inserted into the frame to the middle, into the groove, which will be closer to the outer glass part.
On the other side, a similar operation is carried out. The rope cords must cross. Drowning into the groove until it stops.
The auto glass is placed in the opening. The structure is slightly pressed: not inward, but downward.

The finish is the removal of the rope. It should not be pulled vertically, but horizontally. The seal is being installed. It should first be wetted so that it becomes soft. After drying, the material will harden and fix the edges of the glass.

Required Tools

First you need to select a new canvas. Craftsmen recommend choosing double glass with a polymer layer or single-layer tempered stalinite. Required equipment and related materials:

nylon cord - about 5 meters;
rubber hammer;
slotted screwdriver;
sealant;
anti-corrosion agent and primer.

Preparation involves choosing a comfortable room for work; you also need to select equipment, purchase new glass and dismantle the old fragment.

You can put the old seal on the glass or purchase a new element to make the job easier.

Installing new glass

Let's figure out how to correctly insert the rear window on a VAZ- 2109 . You will need strong rope and a screwdriver. Insert the center of the cord into the middle of the upper half of the seal.

Subscribe to our feeds on social networks such as. VKontakte, Instagram. Yandex Zen, and Telegram: all the most interesting automotive events collected in one place.

Removing the seal

Before installing a new one, the old windshield of the VAZ 2109 must be carefully dismantled. To do the replacement yourself, you will need a slotted screwdriver with a slot width of 10–12 mm. If you plan to reuse the seal, make sure the screwdriver is relatively dull so as not to injure its blade. Before replacing the windshield, it is recommended to remove the windshield wipers. Even bent, they create interference.

READ Changing the oil in the Renault Symbol automatic transmission

Start dismantling the windshield on a VAZ 2109 from inside the cabin, from the middle of the top edge. In profile, the seal resembles the letter “H”. Between the lower halves of the legs of this letter is the edge of the windshield, and between the upper halves of the legs is the edge of the frame, smoothly turning into the roof of the body. You must carefully press the upper leg of the letter “H” closest to you and push it out of the body. Both legs of the upper part of the seal profile will be on the outside of the frame, and you will see the exposed metal of the edge of this frame.

After pushing out the first section of the seal, expand the area step by step. The most difficult step is the first, then the seal goes out almost without resistance. With a little luck, you can push the edge of the seal out without damage. Expand the removal area gradually in both directions from the center until the upper corners of the windshield are free.

If you are replacing the side glass of a VAZ 2109 located behind the rear door, start from the middle of the long side.

Removing the seal

Before installing a new one, the old windshield of the VAZ 2109 must be carefully dismantled. To do the replacement yourself, you will need a slotted screwdriver with a slot width of 10–12 mm. If you plan to reuse the seal, make sure the screwdriver is relatively dull so as not to injure its blade. Before replacing the windshield, it is recommended to remove the windshield wipers. Even bent, they create interference.

Start dismantling the windshield on a VAZ 2109 from inside the cabin, from the middle of the top edge. In profile, the seal resembles the letter “H”. Between the lower halves of the legs of this letter is the edge of the windshield, and between the upper halves of the legs is the edge of the frame, smoothly turning into the roof of the body. You must carefully press the upper leg of the letter “H” closest to you and push it out of the body. Both legs of the upper part of the seal profile will be on the outside of the frame, and you will see the exposed metal of the edge of this frame.

If you are replacing the side glass of a VAZ 2109 located behind the rear door, start from the middle of the long side.

Replacing the rear side glass on a VAZ 2101-VAZ 2107

Welcome! The rear side window of a car - it can break in different situations, for example, it can break if you hit it with a ball or if you just slam the door hard, besides, there are a lot of thieves and different people walking along the streets of our cities, trying to take possession of anything strangers stealing it from the first car they come across, but in order to get into the car they basically break its windows, or if a more experienced person, then use a special hook and sleight of hand to open the car.

Note! In order to change the side window of a car door, you will need tools with which you will remove parts to get to it, these tools include: A set of wrenches and two different types of screwdrivers!

Note! We will give you advice for the future so that you then know what to do in that situation when a crack appears in the glass, namely, have you ever noticed that after a crack appears on the glass, over time it goes a little further until it reaches the end of the glass, so So that this doesn’t happen and you don’t have to immediately go to a service center or garage and replace the glass with a new one, you can extend the life of the old glass, to do this, using a cutter used to cut glass, make a strip across which the previously formed crack will rest against, and thereby She won’t go any further all over the glass!

How to replace the rear side glass on a VAZ 2101-VAZ 2107?

Removal: 1) At the beginning of the operation itself, you will need to get to the window lift mechanism, because in order to remove the glass itself from the car, you must first loosen the window lift cable and remove the glass groove, but in order to loosen the cable and remove the groove, you first need to get to them by removing To do this, cover the trim from the car door on which you are replacing the glass. (For information on how to remove the trim from the door, see the article using the example of removing the trim from the front door; you can see this example in the article called: “Replacing the front glass on a car”, see points 1-4)

Note! Before you start removing the trim, unscrew the button that locks the car door by hand or using a screwdriver (see photo 1), and when the button is unscrewed and removed, unscrew the screw that secures the window sill trim in the front part (see photo 2 ) if you have it of course!

2) Then, when the trim is removed from the door, you will need to remove the protective film, which you may or may not have at all, this film covers the entire window lifter mechanism from dirt getting on it, and this protective film is attached to the adhesive tape by peeling it off , you can easily remove the film from the car door.

3) Now proceed to removing the window sill, there are only four plastic holders that secure it, disconnect all these holders from the door using a screwdriver and then you can remove the window sill from the car door.

4) Next you will need to remove the rear glass groove, to do this, first disconnect the plastic clamp from it (It fits into the hole) that attaches the rod to the groove and after the clamp is disconnected (see photo 1), pick up a wrench and use it to completely unscrew the nut and bolt that secure the rear channel to the car door and then remove it (see photo 2).

5) After removing the groove, insert a handle with which you can lower and raise the window of the car, but only the trim and rosette of this handle do not need to be installed, just put one handle in its place and, holding the glass with your hand, lower it to the very bottom until it stops .

6) Next, unscrew the two screws that secure the pressure plate (Indicated by the red arrow), which in turn firmly fixes the cable and does not allow it to go anywhere.

7) When the screws securing the plate are unscrewed and the plate itself is removed, use a wrench to slightly loosen the nut that secures the tension roller (see photo 1), and after loosening the roller will move and thereby the cable itself will weaken a little; after the cable has loosened, you will need to remove it from the tension roller and from the lower roller which is indicated by the red arrow.

Now use a screwdriver to pry up the chrome inner glass trim and then remove it so that it does not interfere with the removal of the glass; you need to remove it through the top of the car door.

9) And to finish removing the glass, first unscrew the screw that secures the fixed glass to the car door (see photo 1), then completely or just a little (at your discretion) remove the upper seal of the sliding window as shown in photo 2, then tilt the fixed glass forward and remove it and finally lift the sliding glass to the top and tilt it inward, also remove it from the car door (see photo 4).

Installation: Installation of the new glass and all previously removed parts is carried out in their place in the reverse order of removal, but there is only one But! Namely, after installing the new glass and assembling the entire mechanism (assembling the mechanism includes putting the cable on the tension roller, installing the rear groove, etc.), check how your glass works, how it rises, if necessary, adjust the position of the glass groove , and also tighten the cable by moving the tension roller tighter.

READ Replacement of Volkswagen T5 rear brake pads

Replacing the rear window on a VAZ-2109

The rear window of a car is a real assistant for the person behind the wheel. It is through it that you can see everything that is happening from behind and correctly assess the situation. But glass is a very fragile material and if a stone or other heavy object hits it, it can crack or crumble into many tiny pieces. As a temporary solution, you can seal the opening with thick film. But this, of course, is not a solution. In the future, the rear window still needs to be replaced.

Many car enthusiasts put off this work until later, fearing serious costs. In fact, all that is needed is to find money to buy new glass and glue. The rest of the work can be done with your own hands within 1-2 hours.

Replacing the rear window on a VAZ-2109

After this, prepare the necessary tools. To work, you will need new glass (this is logical), special glue (the best option is a 2-component composition), a new rubber seal (you will have to throw away the old one), a string for cutting glass, special suction cups (necessary for holding and lifting the glass). In addition, you will need tape, a knife, sandpaper and solvent.

It is advisable to work in a well-lit room with sufficient space for maneuver. If the weather is good outside, you can set up right next to the garage. The help of a partner when replacing the rear window is very desirable. It is extremely difficult to cope with such work on your own.

So, after carrying out the preparatory activities, you can proceed directly to the work. Here you need to go through three stages:

Remove old glass. This work is done in the following sequence:

When performing work, be very careful and try not to touch the car body (otherwise you will have to restore it as well).

Prepare the opening for installing new glass

Once the old glass has been removed, do not rush to immediately “sculpt” a new one. It is advisable to perform several useful manipulations:

Before installing the lock, it is advisable to pull it a little. Otherwise, its length may not be enough. The wedge is installed as follows. Install the long section first, followed by the short section. If some part of the wedge remains unused, then it is better to cut it off. Otherwise, it will interfere with further work.

When might it be necessary to install new glass? There are two options here - the old glass is damaged or you decide to apply tint. In the first case, everything is clear - you can’t do without a replacement. If we are talking about tinting, then it is better to do this work without dismantling. As practice shows, it is almost impossible to remove the rear window without damage.

Before installation, prepare a thick piece of rope. The length should be such that the rope completely encircles all sides of the rear window. Pay special attention to the quality of the rope - it should be tight. If it breaks during work, it will be extremely difficult to remove the torn piece from the seal.

So, the sequence of actions is as follows:

The final shrinkage of the glass occurs within 3-4 days. This is facilitated by vibrations that are inevitable during movement.

That's all. With the help of such simple instructions, you can install the rear window on a VAZ- 2109 and save a considerable amount. Good luck.

Replacing the rear window of a VAZ 2109: how to do it correctly

1 What types of glass are there for car windows?
2 How to properly remove the rear window of a VAZ 2109 2.1 Preparing the rear window for installation
2.2 How to install the rear window of a VAZ 2109 car

Installation of rear window VAZ 2109

You can drive a car without a rear window. Its technical capabilities are not impaired; it can be used on roads. The only thing is that the driver and passengers of the car will experience great discomfort inside the cabin. All precipitation, dust and wind enter the cabin, and the temperature outside and inside the car will be almost the same, which is especially noticeable in winter. The article suggests learning how to change the rear window on a VAZ 2109, to protect the interior from all weather conditions and external troubles, with your own hands.

Replacing the windshield on VAZ 2108, VAZ 2109, VAZ 21099

Welcome! Most people who periodically use their car have their windshield deformed from time to time, most often this happens from a stone hitting it, a bird flying past, or an accident. The windshield of a car plays a very important role; it creates additional rigidity for the car body, which has a very positive effect in the event of a collision.

Note! It is not recommended to leave a car without the glass removed for a very long time, because if the windshield is missing for a long time, the car body may become distorted; of course, you won’t see anything by eye, but this will make itself felt when installing a new glass!

What other glasses can be replaced using these instructions? Using this article, you can replace other fixed windows on a Samara family car in exactly the same way, since their replacement is carried out in the same way; fixed windows include:

How to replace the windshield, also known as the windshield, on a VAZ 2108-VAZ 21099?

Note! The glass on the Samara family car is secured with a rubber seal and therefore it is much easier to remove, unlike more modern cars, for example the VAZ 2110, on which the windshield is directly glued into the body!

1) First, in order to successfully remove the old windshield, remove the wipers from the car. (How to remove wipers, read the article: “Replacing windshield wipers”)

2) Now use a screwdriver to unscrew the screws that secure the side pads on both sides.

4) Now tuck the edges of the rubber glass seal behind the body.

Note! After the edges are tucked in, press the upper corners of the glass from the interior and gently push it out. The blown-out windshield should be taken care of by an assistant standing outside!

Note! Before installing new glass, inspect the rubber seal for defects and, if possible, replace it with a new one. But installing a new seal on the glass will be much more difficult, because as a rule, the old seal is more elastic, and therefore can be installed on the glass much easier!

1) At the beginning of the operation, rinse the grooves of the rubber seal with water and then blow it with compressed air, thereby drying it completely from water.

2) After this, put the rubber seal on the windshield.

Note! After the seal is installed, lubricate the seal groove with WD-40 or something similar, or with soapy water!

3) Then use a strong cord or rope, and then, by hand or using a screwdriver, insert it all the way strictly into the first groove of the seal, which is located closer to the inside of the glass. (If you don’t understand which groove we’re talking about, then play the video below, and you’ll find out everything in detail)

Note! When the rope is completely recessed into the first groove, be sure to close it so that the ends of the rope overlap at the very bottom of the glass!

4) Next, install the glass together with the rubber seal in the opening in its place. When installing, make sure that the ends of the rope are inside the cabin.

5) Next, ask an assistant to lightly press the glass from the outside to the opening, while you gradually pull the rope out of the seal from the inside.

Note! When you begin to pull the rope, make sure that the edge of the seal is pulled over the edge of the opening. For greater confidence, you should press with your hand from the outside the place where you are pulling the rope from the inside!

Additional video materials: Removing the windshield from the car is not difficult, but installing new glass in this place will require some effort. Below we have prepared a video that describes in detail the entire process of installing new glass.

READ Honda Accord Rear Caliper Repair

Important! To avoid various injuries, it is best to remove the windshield together with an assistant!

Replacing the rear window of Lada 2108 (VAZ 2108)

rear window replacement

Rear window The car is a real assistant for the driver. It is through him that we see what our client can do, what is happening behind us, and correctly assess the situation. However, glass is a very fragile material, and if a stone or other loose object gets caught in it, it can crack or shatter into a large number of small pieces. For a temporary solution, of course, cover the gap with a thick film. But this, of course, is not an option. In the future, the rear window will need to be replaced.

The car owner may have postponed this work until later, fearing serious expenses. In fact, our client is left to do everything possible to find the funds to purchase new glass and glue. The rest of the work is completed independently within 1-2 hours.

Replace the rear window on a VAZ-2109

Before you go to the store differently in the market and get a new rear window for your car. It is important that it fits your model correctly (pay special attention to heating and design features).

Then prepare the necessary tools. To get the job done you need. new glass (this is reasonable), special glue (ideally a two-component composition), new sealing rubber (you will need to throw the old one), a string for cutting glass, special suction cups (necessary for holding and lifting the glass). Additionally, tape, a knife, sandpaper and solvent are useful.

It is best to work in a well-lit area with sufficient maneuverability. If the weather outside is perfect, you can stay right next to the garage. Helping your partner replace the rear window is highly desirable. It is difficult to cope with such work without outside help.

What you need after the previous steps, start specifically. There are three steps here:

Remove the old glass. This work is performed in the following order:

Removing glass from the trunk lid 2109 2114

Conventional glass

even a schoolboy can control the trunk lid.

Removing the rear window on a VAZ 2109 from Seryoga)))

Is it correct to remove the rear window

with nine nine.

When doing the work, be very careful not to touch the surface. car body (otherwise you will have to restore it).

Prepare a gap for installing new glass

When the old glass fails to take off , do not rush to “sculpt” a new one right away. It is better to perform some of the necessary manipulations:

Before installing the lock, it is better to pull it a little. Otherwise you won't like its length. The wedge installation is done like this. Install the long section first and the small section at the end. In this case, some part of the wedge remains unused; it is better to cut it. Otherwise it will interfere with future work.

install rear window
.

When should new glass be installed? There are two options. the old glass is damaged or you decide to glue a shadow. At the beginning, our client remains clear. do without a change. In this case, we are talking about tinting; it is better to do this work without disassembling. Practice shows that it is almost impossible to remove the rear window without damage.

Before installation, prepare a thick piece of rope. It is advisable that the length of the rope exactly matches what was left for our client on the side of the rear window. Pay special attention to the quality of the rope. he must become strong. If it breaks during operation, it will be difficult to remove the broken piece from the seal.

What you need to do is:

The final shrinkage of the glass occurs within 3-4 days. This is facilitated by vibrations that are inevitable when moving.

Conclusion

Replacing the rear window of a VAZ 2109

You can replace the rear window of a VAZ 2109, as mentioned above, yourself. Before installing new glass, you must remove the old one.

Removal

To do this, you should:

Take a screwdriver and insert it into the seal that holds the glass. It should be inserted approximately 5 mm.

Note: it will be possible to insert the screwdriver deeper, but you should not do this, as you may make a hole that is too deep.

Push the seal out. First you need to pull out a small piece. The downside is that you cannot pull out the entire seal by pulling it. It's just quite fragile, so it breaks quickly.
Carefully move the screwdriver a few cm. Tear off another piece of the seal.
Step by step you can get rid of everything.

Note: since the glass is secured with a seal, as soon as it is gone, it will begin to wobble. Therefore, you need to get rid of the seal slowly and carefully so that the glass does not fall out before it is needed.

After the seal has been removed to the upper side corner, you can begin to remove the glass itself.

Replacing glass on a VAZ 2109

Don't try too hard when removing the glass. Usually it cannot be kept completely intact.

It certainly cannot be reused. The main thing is not to damage the body of the vases, otherwise additional repairs will be required.

Preparing for installation

Before you begin installing new glass, you must do the following:

Wipe the edges with degreaser to make it easier to install the seal. That is, the cleaner the glass, the better the seal will fit.

Note: If the old seal was removed carefully, it can be reused. However, in order to remove it carefully you will have to suffer. Therefore, it is advisable to use a new seal.

 Put on the seal. First, it is distributed in the corners, and then pressed against the sides of the glass.
After this, you should install a lock, which is a small wedge that looks like the letter P. It needs to be inserted so that it is in the center of the seal, but runs along the entire perimeter.

Note: The wedge should be stretched slightly before installation. If you don't do this, then there simply won't be enough. Usually you can stretch it up to 20 cm!

The wedge is installed as follows: first you need to insert the long part, then the short one. This needs to be done around the entire perimeter of the glass. If a small part of the lock remains intact (that is, it is redundant), then it must be cut off, otherwise it will interfere with subsequent actions.

Installation

Replacing glass on a VAZ 2109

Installing the rear window may be necessary when replacing it, or when tinting it. Although usually, tinted glass is new, since, as stated earlier, it is almost impossible to remove the rear window without damaging it. In order for the installation to be completed successfully, you should find a rope that is long enough to completely surround the sides of the rear window. It should be quite tight, since it cannot be allowed to tear. If part of the rope remains in the seal, it will be very difficult to pull it out. The installation of a new rear window should be done as follows:

Determine where approximately the middle of the rope is. Insert this part into the upper side of the seal.
The seal has two grooves. You need to find the one that is closer to the top of the glass.
Use a screwdriver to insert the rope into the groove until it stops. You need to insert the rope to the middle of the glass area. We need to stop there. One end of the rope should hang freely on one side. In this case, the second one must be stuck into the seal.
On the opposite side, you should also insert the rope until it intersects with the end of the previous rope.
When they intersect, the end of one must be placed on the end of the other.

Note: the ropes must overlap each other. The overlap should vary between 5-10 cm.

The free ends of the rope should be pulled into the cabin.
Only after this can glass be placed in the opening. It is advisable to have someone help, as it is quite heavy and can be accidentally dropped. The bottom of the opening should fit into the outer groove.

How to insert a rear window

Rear view glass for a car, screwdriver, rubber seal, elastic lock, 2 m cord.

The rear window for a car is selected strictly according to the modification of the car, since the shape of such glass is different for all cars. Before you begin, inspect the new rear view glass for chips, cracks, or other defects. First, you need to remove the old glass to replace it with a new one. Take a flat head screwdriver. This tip will help you pry off the seal on the inside and outside of the glass, which all VAZ cars are equipped with.

Using a screwdriver, first push out the outer seal around the entire perimeter, then the inner one. This way you will free the rear window from its rubber support. Then you need to squeeze it out. Push the glass with force from the inside; on the other side, someone should support it so that it does not fall and break.

If the glass does not squeeze out, it means that you have not bent the rubber seal on all sides well enough. Repeat the procedure of moving the seal away with a screwdriver again around the entire perimeter and try to squeeze out the glass again.

Apply new rubber seal around the entire perimeter of the rear window. Insert the elastic lock into the corresponding groove. To make it different from a regular seal, it is produced shiny. Now take a two-meter cord. It must be placed on the top and sides of the seal. Do not lay the cord below. Both ends of the cord of the same length should be in your hands.

Carefully take the new glass with both hands and insert it into the lower groove on the seal, as if rubbing it into it. Do not press hard, but confidently on the glass (it is better to do this with someone together), while pulling the cord at both ends, first on one side, then on the other. In this case, the cord will help the seal to disconnect. In the end, you will have a cord in your hands and the glass will accurately fit into its place in the grooves of the rubber seal.

how to replace rear window in 2017

How to properly remove the rear window of a VAZ 2109

You will need to replace the rear window after an accident, tinting or unexpected damage to the installed element.

Installing the rear window of a VAZ 2109

Before installing new glass, you must remove the old one. For this:

The screwdriver is inserted into the seal that holds the glass. You need to deepen the tool by about five millimeters.

Tip: There is no need to insert the screwdriver deeper, otherwise the hole will be too deep.

The seal is pushed out.
First, a small piece is pulled out.

Tip: Do not pull on this piece and try to pull out the entire seal; due to the fragility of the product, it can be torn.

The screwdriver is carefully moved a few centimeters, as shown in the photo.

The screwdriver is inserted into the seal

Another small piece comes off from the seal.
This continues until the seal is completely removed.
Removing the rear window of a VAZ 2109.

Tip: It is often not possible to keep old glass intact, but this does not matter. The main thing is to keep the body intact, otherwise it will need to be repaired.

Preparing the rear window for installation

The instructions indicate that before installing a new rear window, you must first do the following:

Wipe the edges thoroughly with degreaser to facilitate installation of the seal. The cleaner the glass, the better the seal will fit.

Tip: If the old seal can be removed carefully, it can be reused. But this is difficult to do. Therefore, it is advisable to use a new seal.

Put on the seal. Spread it first in the corners and then press it onto the sides of the glass.
Install the lock, which is a small wedge resembling the letter P. It is inserted so that the device is located in the center of the seal, but runs along the entire perimeter of the inserted element.

Before installation, the wedge must be stretched slightly. Otherwise, it may not be enough. Usually it stretches up to 20 cm. The wedge is mounted as follows:

The long part is inserted first, then the short one. This needs to be done around the entire perimeter of the rear window. If part of the lock is left over, it needs to be cut off so that it does not interfere with subsequent actions.

How to install the rear window of a VAZ 2109 car

To successfully replace the rear window, you need to purchase a strong rope, the length of which is the same as the perimeter of the glass. The order of work is as follows:

The middle of the rope is determined and this part is inserted from the upper side of the seal.
There are two grooves on the seal. The groove is located closest to the top of the rear window.
Using a screwdriver, insert the rope into the groove all the way to the middle of the glass area.

It turned out that one end of the rope hangs freely on one side, the other is stuck into the seal.

The rope is inserted from the opposite side until it intersects with the end from the previous rope.
After crossing, you need to place the end of one on the other, the ropes should overlap each other. The overlap should be from 5 to 10 centimeters.
The loose ends extend into the interior.
The glass is placed in the opening. The lower part of the opening fits into the outer groove.
Lightly presses on the glass. It should press well into the seal and fit easily into place.
The rope on both sides pulls towards itself.
Half the rope is stretched to the bottom corners of the rear window.
With a smooth movement, the glass slides into place.
The rope is pulled out and the glass is carefully seated in the opening.
The location of the seal is controlled so that it does not come out.
The glass is seated in the opening all the way.

Replacing the rear window of a VAZ

If you have ever watched a specialist change the glass on a VAZ, no matter the rear or windshield, changing the rear window yourself will not be difficult. And if you’ve never seen it, that’s okay too.

By replacing the glass yourself, you will acquire a skill that will be useful in the future. For example, your friend will ask you to change the glass. And you will do this to him out of a friendly disposition. If a friend or stranger asks you, you can even earn money.

Rear window replacement

Replacing the rear window of a VAZ 2109

You can replace the rear window of a VAZ 2109, as mentioned above, yourself. Before installing new glass, you must remove the old one.

Removal

To do this, you should:

Take a screwdriver and insert it into the seal that holds the glass. It should be inserted approximately 5 mm.

Note: it will be possible to insert the screwdriver deeper, but you should not do this, as you may make a hole that is too deep.

Push the seal out. First you need to pull out a small piece. The downside is that you cannot pull out the entire seal by pulling it. It's just quite fragile, so it breaks quickly.
Carefully move the screwdriver a few cm. Tear off another piece of the seal.
Step by step you can get rid of everything.

Note: since the glass is secured with a seal, as soon as it is gone, it will begin to wobble. Therefore, you need to get rid of the seal slowly and carefully so that the glass does not fall out before it is needed.

After the seal has been removed to the upper side corner, you can begin to remove the glass itself.

Removing and replacing the windshield on a VAZ 2109

To change the windshield on a VAZ 2109 , you need to purchase a new transparent element, prepare equipment, study the instructions for dismantling the old blade and installing a new one. Replacement of this automobile element will be required after an accident, as well as in the presence of numerous microcracks or deformation of the body part. to insert glass with your own hands, if you take into account the main nuances of the process.

Removing the seal

Removal of the sealing element will be required when replacing the windshield frame or the most transparent part. Removal is carried out from the passenger compartment, strictly according to the instructions:

The windshield wipers are removed.
Use a slotted screwdriver with a width of 10–12 mm to pry off the seal. The tool should be used carefully so as not to damage the rubberized material if you plan to use it in the future. You should start from the middle of the top edge. By pressing the top part with a screwdriver, the glass can be easily removed.
When part of the sealing fragment is removed, the auto glass will already be movable. It is necessary to expand the area between the metal and the seal.

When you manage to remove most of the rubber, it will be possible to pull out the glass structure.

How to remove and install rear window

The rope is inserted into the frame to the middle, into the groove, which will be closer to the outer glass part.
On the other side, a similar operation is carried out. The rope cords must cross. Drowning into the groove until it stops.
The auto glass is placed in the opening. The structure is slightly pressed: not inward, but downward.

Replacement principle

When replacing the windshield on a VAZ 2109 , it is necessary to take into account its dimensions. When purchasing, it is important to compare the auto glass article number with the data indicated on the factory element. The size of the frontal fragment is standard, as on all VAZ models. Rules and nuances of replacement:

The rubber seal should fit tightly in all corners, and the structure itself should fit into the side, top and bottom sides of the frame.
Installation of glass requires the installation of an internal lock. The locking mechanism is an important element during installation; it is shaped like a wedge. It needs to be installed in the center, but the wires should be routed around the entire perimeter.
Careful removal of the structure is required first. It is important not to damage the frame.
If the size is slightly off, it can be easily corrected with a rubber mallet.
Anti-corrosion treatment of the element and frame is also necessary. It is recommended to use a rust modifier and primer. After drying, sealant is applied to the frame, then sealing material is installed. The external and internal grooves of the frame are lubricated.

The length of the nylon cord is equal to the size of the car glass. It is better to purchase this material with a diameter of at least 4 mm. The quality of the cord is checked by touch; it must have a slippery surface. The nylon fits into the grooves of the seal.

Removing old glass

To understand how to remove a VAZ windshield, you should refer to such a device as glass holders. A device with vacuum suction cups will allow you to carry out the process in an accelerated mode. This tool is installed on the sides of the glass. After fixation, a jerk is made upward. You can't do this without an assistant. If the glass holder is not found, a screwdriver will help.

Using a slotted screwdriver, the remaining sealant is pushed out. An assistant must hold the glass to prevent it from falling out of the frame. If the work is carried out alone, then you can play it safe by laying soft material on the hood of the car. Then the glass is pushed out of the cabin.

Required Tools

First you need to select a new canvas. Craftsmen recommend choosing double glass with a polymer layer or single-layer tempered stalinite. Required equipment and related materials:

nylon cord - about 5 meters;
rubber hammer;
slotted screwdriver;
sealant;
anti-corrosion agent and primer.

Preparation involves choosing a comfortable room for work; you also need to select equipment, purchase new glass and dismantle the old fragment.

You can put the old seal on the glass or purchase a new element to make the job easier.

Sources:

https://vaz-russia.com/remont/zamena-zadnego-bokovogo-stekla-na-vaz-2101-vaz-2107.html https://ru.megasos.com/wiki/zamena-zadnego-stekla-na -vaz-2109 https://vaz-russia.com/remont-vaz-2108/zamena-lobovogo-stekla-na-vaz-2108-vaz-2109-vaz-21099.html https://autofluids.ru/remont -i-servis/kak-vstavit-zadnee-steklo.html https://infokuzov.ru/remont/steklo-lobovoe-vaz-2109