How to install a winch on a UAZ Bukhanka

UAZ 3962 “Grey” › Logbook › Installing a winch.

I bought the winch almost immediately after buying the car.
Having studied I-Net, I came to the conclusion, agreeing with many practitioners, that the power of the winch should be twice the maximum permitted weight. I have a UAZ 39625 with a title of 2720 kg * 2 = 5440. A friend recommended the store polniyprivod.ru/, where I bought a winch for 17,000 rubles. Electric Winch 12000 with wired and wireless remote control, 30 m steel cable and 3 connectors (one for the front, one for the rear of the machine and one for the winch). As I later found out, the connectors hold no more than 200A of current, and the consumption of my winch at maximum loads can briefly exceed 400A. There was a need to find the appropriate wiring. Again, many days of searching for information, formulas, etc. Again, I had to rely on the opinion of experts that for every 10A a cross-section of copper wire (core) of 1mm2 is required. Accordingly, I took welding wires of about 40 mm2. The longer the wire, the more the losses in the conductor increase; accordingly, it is necessary to increase the cross-section of the core. The standard wires were short, so I had to disassemble the solenoid block and replace the positive wire with my own. Thanks to the guys, in the workshop they crimped the terminals with a special tool, put on the casings, it turned out no worse than at the factory, but it’s just enough from the bumper through the hole in the tunnel under the speedometer cable to the battery. In the future, I want to replace the battery (battery) with a 90 Ah instead of 60, replace the generator with an appropriate one (I’m still studying the characteristics) and install a winch power cut-off relay from a button on the panel (many complained that it sometimes shorts inside and the winch rewinds without responding to the buttons of the remote control and As a result, it breaks the bumpers, platforms and its own body). Also in winter, on the advice of friends, I will shorten the cable by 10 meters. When winding too long a cable to the side, a heap accumulates at the edge of the drum, which can break the transverse fastenings of the winch if you don’t keep track. So it’s better to interchange with a short cable several times. I would like to share my development for installing a removable winch on a non-lifted UAZ 39625 (loaf, tablet) with standard bumpers. The task was unusual (I set myself the Technical Assignment), install the Electric Winch 12000 winch on a loaf without changing the appearance and without making changes to the design, so as not to register with the Technical Department, not to worry about technical inspections, not to cut the bumper, etc. Moreover, the winch must be removable and installed both front and back for all occasions. The winch platform should not be lower than the edge of the bumper. The rear footrests and standard towbar should be preserved (they are very comfortable). Centering the winch in the middle is recommended, but not required. Inspired by the idea on YouTube:

After much research on the Internet, I decided to make an American towbar: a square pipe is attached to the frame of the car, a square pipe of smaller diameter is inserted into it, welded to the platform with the winch and secured with a pin or a cotter pin. Having told the idea to the specialists (the head of the metalworking shop), they came to the conclusion that the lateral loads of the UAZ require a minimum of 2 square meters. On the Internet I found a picture with the sizes of the holes and the distances between them on the winch platform for the UAZ Patriot on the forum uazpatriot.ru/forum/viewt…pic.php?t=18614&start=210,

They coincided with the drawing in the instructions for the winch and sent it to the workshop. They did it in a week, slowly, but efficiently. The only point is that this platform should immediately be attached to the frame of the Patriot, and on my copy, on the right and left, I cut off the protruding ears with a grinder. We found a rectangular pipe, but there was no smaller diameter! We got out of the situation by taking solid pieces of metal, machined them and welded them to the site. The weight turned out to be the same! All that remains is to attach it to the frame. The hooks must first be removed. They are attached to the frame not with bolts, but with rivets, and are installed “hot”. I spent several hours sawing off the heads of each rivet with a grinder on both sides. I tried to knock it out - it was useless. I had to drill out first with a small drill, then with a large one, and only then was I able to break out the hooks. The left one also turned out to be welded to the frame along with the steering gear mounting spar - but it still broke off! What a pleasure! Next, I measured the width of the frame with a tape measure, estimated the width of the plate, and sent the drawing drawn on my knee to the workshop. Afterwards, the finished plate was attached to the frame, holes were marked on it along the holes from the hooks and again to the metalworking shop. The next time we assembled a ready-made structure.

During final assembly there were many nuances. For example, a piece of rectangular pipe used to grind squares for the winch platform turned out to be from a different batch than the pipes welded to the frame platform. It took a long and tedious time to grind off the excess with a grinder. And inside these pipes there is also a protruding seam! The metal moves slightly when welding, so the squares that had slipped on the site were straightened out with a hefty sledgehammer. In general, they created problems for themselves. When I started cutting holes in the bumper, I realized that they had climbed into the place where the crooked starter was inserted! It was necessary to move the mount by 3 cm...

At the moment, the winch is connected according to a temporary scheme; the wires are simply attached to the battery terminals with nuts. Installation is also easy in 4 minutes. The front grille is removed, a platform with a winch is inserted, it is fixed with 4 pins, which are pinned, the wires are passed to the battery through the hole for the speedometer cable, the grille is returned to its place. In the future, it is necessary to move the solenoid unit into the cabin, remove the sockets from the welding disconnectors (purchased sockets will not be suitable for the current load) in the front and rear. I will route the wiring from welding cables in a corrugated structure along the frame. As soon as I do it, I’ll post it.

Source: www.drive2.ru

Winch configurations

The additional equipment of the electric winch includes:

• the device itself, • a cable on the drum, • a hook, • a joystick • a remote control • a shift lever • a solenoid block • cable rollers (they are called lips) • fastening bolts • instructions for using additional accessories are not included in the standard kit, therefore, If you decide that you cannot do without a corrosion-protective sling or pulley block, purchase them separately.

When purchasing, you should pay attention to the rollers on which the cable is laid. The distance between the vertical and horizontal lips should not be greater than the thickness of the cable, otherwise it will bite when winding.

UAZ for the hunter: Three winches for one Loaf

You can scold the loaf, you can accuse UAZ of being retrograde, but so far no one in Russia has come up with a way to replace it. For example, take a very good version of the UAZ for a hunter.

We built a car for the specific needs of a specific person and assessed the investment; Hunting takes up quite a lot of time in a customer’s life and is not the least of his interests.

Preparation and correct final product. The air intake is organized through a hole under the roof - a useful solution for fans of “swimming”.

Headlight protection is not a sham, but real steel. Well, it looks evil.

The additional canister on the gate for the spare tire increases the load on the gate, but makes very good use of the space.

In terms of mechanics, the engineers took a classic approach: a 65 mm body lift, Ironman off-road shock absorbers, pneumatic axle locks, a transfer case kit with a 3.3 lowering and higher-torque main pairs (5.2).

To install Simex Jungle Trekker tires mounted on Wheels steel wheels, the arches had to be trimmed. RIF hubs are responsible for disabling the front axle shafts.

To get into the interior of the tall car, a real retractable step was installed.

A house for talking about hunting. Or fishing. Or…

The interior of the off-road bus was divided into cargo and passenger areas.

There is no luxury ahead - only utilitarianism.

The standard front seats have been slightly adjusted to match the car's condition.

In the stowed position, the table folds up and does not get in the way.

The passenger compartment is modest, but not without a certain luxury.

Place for shmurdyak is always a sore subject for travelers by car.

The cargo-passenger version would not fit here without the need for a large trunk.

Moreover, there was room for a spacious shelf above the cargo area.

The trunk can be washed under pressure - everything is sealed and will not get into the cabin.

Special rails are installed for loading the carcass.

Runva 9500 winches are installed in the power bumpers, but in order to find the third winch, you will have to open the trunk.

A small winch for the quad is installed inside and is designed to drag the carcass of a hunted animal into it.

Electric windows made it possible to use the space for installing speakers.

In the stowed position, the canister does not extend beyond the reserve. It is almost impossible to damage it.

The final preparation of Loaf for life in the forest was completed by the Raptor protective coating.

The result was a good bus, capable of traveling along unknown paths of dense forests.

Nothing superfluous, but you will have to climb high for a shovel.

Source: www.uaz.ru

Recommendations for installation and operation

Designed for installation of winches 5000-12000. It is attached to the front part of the car frame, for which the existing standard holes are used.

The platform can be installed both with a standard bumper (excluding Hunter with a plastic bumper), and when using Autoventuri-RIF power products, if they are not initially equipped with a platform for a winch (in particular RIF012071).

High-quality steel and polymer powder coating guarantee high corrosion resistance under any operating conditions (2-year warranty on paint coating in the absence of mechanical damage).

As a rule, installation of additional equipment should be carried out in special workshops. If this is not possible, you can install the winch on the car yourself, without the help of a specialist. Here are some tips for installing additional equipment:

Determine the location of the winch. That is, decide where it will be installed in front or behind the car.

Preparing the site for winches begins with selecting a piece of channel. This piece should fit perfectly into the car frame.

We install the winch using the bolts that are included in the package. To avoid damaging the winch when tightening the bolts, place them on the corners.

Install the winch straight, it should not be at an angle, otherwise there is a risk of breaking the unit in half when pulling the car.

Experienced people recommend removing the standard generator and replacing it with a generator from the Bychok bus. The 90-amp Bychka generator will allow you to pull out the car without the risk of draining the battery.

When winding the cable onto the drum, make sure that the cable lays flat, this way you will extend its service life.

It is recommended to remove the solenoid block under the hood, or better yet, directly into the interior. Alternatively, your car will drive through puddles and creeks, and when it gets wet, the unit will close.

When operating a winch, always throw a jacket or thick rag into the middle of the metal cable. The cable can break under load, and it’s good if there are no injuries.

That's probably all. Of course, each UAZ-469 owner will decide for himself which winch to purchase; we hope that this article will help you better navigate the world of additional equipment for the UAZ driver.

We make a winch for a UAZ Bukhanka with our own hands

The question of how a winch is made on a UAZ Bukhanka will certainly be of interest to those owners of an all-Russian SUV who do not yet have this device installed on their car. And it can, under certain conditions, make life much easier for the owner. And for those who are constantly accustomed to traveling off-road, hunting or fishing, a winch is an absolutely irreplaceable thing. As they say, where an ordinary passenger car cannot pass, a Russian SUV will definitely get stuck! But jokes are jokes, but we have to get out. And here an ordinary winch comes to the rescue.

The winch on the UAZ Bukhanka can be installed mechanical, electric, or hydraulic. And there are also hand winches, driven by human physical force using a lever. All of these options have their pros and cons. But let's talk in more detail about each of them.

The device is connected to the shaft. The source of interaction is transmission. The winding speed is controlled by decreasing/increasing engine speed. Other advantages include high stability and traction power (achieved by motor torque). This type of winch is driven by the transfer case of the car. The main disadvantage: the winch directly depends on the serviceability of the motor; for successful operation it requires a properly running motor. If there is a problem with this node, it simply stops functioning.

This kind of device is attached to almost any car that comes with a hydraulic mechanism (UAZ included). The advantages: it works quietly and has small dimensions, powerful and has high performance. Of the minuses: its operation will be directly related to the hydraulic booster (if not, then the device will not function).

For homemade winches, as a rule, starters or generators can be used for loading. The electric winch can also operate on a dedicated electric motor installed in the car. But usually such a winch is mounted on the basis of a converted starter and must operate at sufficiently high speeds, otherwise it will not cope with a heavy machine. Therefore, some install batteries with large power reserves on their cars. Pros: high speed of operation, autonomy (can work regardless of whether the motor is on/off), simplicity of design. Of the minuses: it does not tolerate moisture well, the battery drains quickly.

Since a purchased winch, and even more so its installation, is not always available (most often due to the high cost), craftsmen have gotten used to constructing the structure with their own hands. By the way, this is quite possible to do if you have the necessary tools and certain skills. And yet, our homemade device must have a high torque, otherwise it simply cannot be used for a heavy UAZ (for example, to pull the car out of a mud hole). And most importantly, building a homemade winch will allow you to save a lot of money!

We make the structure itself using a welding machine and an angle grinder from pipes, 5 mm thick sheets of metal for the manufacture of drum discs, a chain with sprockets and a hub. All work is carried out clearly according to pre-drawn drawings. And remember the golden rule: you need to measure repeatedly before cutting.

After the winch structure itself is ready, you can install it on the UAZ Bukhanka. First, we carefully prepare the site. But first we decide: we will install the winch in front or behind. Typically, many people prefer a front location in the central part of the bumper. A channel is usually used as a platform for the device. A piece of it fits well on the car frame.

Naunet SP

Naunet SP is one of the largest Russian domain name registrars. We offer the widest range of domain registration and maintenance services, website hosting services, as well as various additional services.

Working with Naunet SP you get:

Service from the oldest registrar in the national zone .RU
Domain registration in all major zones
Service for selecting domain names by keywords
Simple domain registration in three steps
Convenient service management via a web interface
Managing services from a mobile device
24/7 technical support with call tracking system
Wide range of payment methods
Direct deposit of funds directly to the registrar
Modern Administrator protection against spam
Protection of the Administrator’s personal data
Protection against domain name theft
Registrar professional activity insurance
Secure online transfer of domain names
Domain store
Full line of hosting services and additional services
Domain Administrator paper certificate
Free service “DNS – Basic”
Passport verification at the request of the Administrator
Free SMS notification about important domain operations
Crediting the cost of domains when ordering other services*
Discounts and Promotions
Partnership programs
Professional application programming interface (API) for service management

The electric winch on the car is an optional equipment. This is a special device for moving and lifting loads; it also serves to self-pull out a car stuck in the mud.

Winches come in three types: mechanical, manual, and electric. It is clear that it is better to choose an electrically driven winch. Because, if necessary, there will be less work.

Today there are a huge number of similar devices on the market, and it is difficult for an inexperienced buyer to choose which brand to prefer.

All about tuning

How to install a winch on a UAZ 469

The main task of a winch is to tow a car or other heavy load by winding a cable. It is an integral part of every car whose drivers often drive off-road, find themselves in extreme conditions, or live in places where roads are often washed out by rain.

Since the majority of UAZ drivers are precisely those people who prefer extreme driving, installing a winch is a top priority for them. To avoid problems that often arise with this mechanism, when purchasing you should pay attention to some parameters of the winch.

How to install a winch on an SUV

A homemade winch can be attached to both the front and rear bumpers. But it is best to place it on the central part of the front bumper on the lower side, as this will simplify the use of the device. If the UAZ model is equipped with a plastic bumper, it will definitely have to be replaced, since it will not withstand the total weight of the SUV, which, as a rule, exceeds 2000 kg. The best solution would be to replace it with a bumper made of high-strength steel.

The bumper must have a platform for a winch made of iron plates with a density of at least 5 mm. After this, you need to mark the points for the openings and drill them using an electric drill.

An iron platform for the traction device must be placed on the front bumper. But do not rush to install the winch itself, since it is placed last. First you need to attach the iron plate to the bumper, and then place the traction device on it.

If it is not a mechanical winch, but an electric one, you will need to connect its controller to the SUV's power supply. The circuit is connected by connecting the plus to the positive and the minus to the negative terminal of the power supply network. After successful installation, it is necessary to check the functionality of the structure; it is advisable to do this in the field.