Replacing headlight bulbs on a Largus

Removal and installation of the headlamp is carried out in the event of its replacement, modification or tuning. The process is not complicated, but it requires removing the front bumper, because... Below it are the lower headlight mounting screws. Let's look at the instructions for replacing a Largus headlight with your own hands.

1. Disconnect the wires from the headlight bulbs (1. low/high beam - remove the cover and pull out the block with the wires. 2. remove the turn signal and clearance sockets. 3. if there is a hydraulic corrector - slide the cover along the cable sheath, unclip the latch, turn and remove the actuator mechanism);
2. Unscrew the three fastening screws around the perimeter of the headlight (No. 1, 3, 4), using a 10mm wrench, and remove the headlight.

Installing the headlight is done in reverse order. The process of dismantling the headlight is also shown in the video:

A similar procedure is performed on Renault Logan. Have you ever had to remove the headlights on Largus yourself? Were there any difficulties during this operation? Let us remind you that we previously looked at replacing lamps in the headlights of a station wagon and a van.

Key words: headlights Lada Largus

The headlight unit is removed in case of body work or when replacing it. The glass on the Lada Largus headlight block is glued in and if it is damaged, the headlight block is completely replaced (along with it). Replacement operations are shown using the example of the left headlight block. The right headlight unit is replaced in the same way. The main problem when removing the front headlight of a Lada Largus car will be the need to remove the front bumper.

What kind of bulbs are in the headlights?

• Low and high beam lamp - H4, power 12V, 60/55W;
• Bulb dimensions - W5W, power 5W;
• Front turn signal lamp - PY21W;
• Fog lamps - H11, power 12V, 55W.

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

1. Turn the lid counterclockwise;
2. Remove the cover by releasing the latch.

1. Remove the block with wires by unclipping the lock;
2. Remove the rubber cover by prying it off by the edge.

1. Unscrew the lamp clamp to the side;
2. Remove the headlight bulb.

Installing a new lamp in the Largus headlight is carried out in the reverse order. You need to hold the lamp by the base; it is not recommended to touch the bulb with your fingers. If necessary, wipe the flask with a microfiber cloth that does not leave lint. The process of replacing the H4 lamp is also shown in the video:

Daylight

If the optics on the Lada Largus are faulty, replacing the light bulb will require the following algorithm:

1. The rubber pad is removed, which serves as protection for the electrical unit.
2. The block with the installed wires is removed.
3. The U-shaped lock moves (moving to the side and back).
4. The electric lamp is pulled out.
5. The detail changes.

It is important to remember the orientation of the cartridge - two teeth at the top, one at the bottom.

How to replace a Largus lamp:

1. When installing, hold the lamp by the base or use microfiber, otherwise marks will remain on the electrical appliance and it will burn out faster;
2. Repeat all the above steps to remove the optics in reverse order.

It is recommended to replace both bulbs at the same time. This will prevent unexpected overheating of the remaining part and ensure the same light beam parameter.

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

1. Remove the fender liner by removing the screws;
2. Disconnect the block from the lamp by pressing the lock;
3. Remove the lamp by turning it a third of a turn counterclockwise.

Install the lamp in the reverse order.

Attention! In practice, replacing lamps in a Largus headlight is much easier. In other words, it is not at all necessary to remove the battery and fender liners (lockers). If you get the hang of it, you can access all the headlight bulbs from the engine compartment.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. It is convenient to find the answer to your question based on the content.

Special lighting

The fog lamp in the car modification cannot be reached through the engine compartment. The driver of Largus will have to crawl under the car:

• remove the screws;
• remove the fender liner;
• press the latch and separate the block from the lamp;
• Turn the burned out light bulb counterclockwise a third of a turn;
• extract element;
• insert a new one into the cartridge;
• Install the lock in reverse order.

Finally, the functional operation of the devices is checked. If the headlights dim or flicker, the contacts in the system are not secure enough. Causes of malfunction:

• contamination of electrical wiring;
• oxidation of contacts;
• manufacturing defects.

To eliminate the last reason for incorrect lighting operation, it is important to pay attention to the reliability of the manufacturers whose products are purchased. For Largus, it is recommended to choose only original optics.

Replacing a light bulb on Largus is a simple and quick process. Each car owner is able to perform the work independently. To achieve results, it is important to choose quality products, as well as adhere to safety precautions and instructions. Installing a new fog light bulb poses some difficulty, but even this can be handled with due care.

How to change the low/high beam lamps on Largus, as well as the dimensions

A note about what kind of lighting lamps are installed in the Largus headlights; which of them are low/high beam, and which are responsible for the side lights. How to change lamps yourself. How much do originals and analogues cost in Yaroslavl?

Good day, future and aspiring gentlemen Largusovod!

On Largus, the low/high beam and headlight lamps often burn out. At least for 70 thousand I have already changed it five times on each side.

The following light bulbs were installed on my car:

1. Low/high beam: halogen, Osram H4 12v 60/55w. (art. 64193). Price from 109 rub.

There are many analogues. Here are some of them:

370 rub. General Electric (34454)

117 rub. Valeo (032007)

2. Front dimensions: halogen baseless 12V Osram (art. 2825). Price from 17 rub.

26 rub. Lynx (L12805)

9 rub. Fortluft (2825)

3. Rear dimensions: two-pin with filament, base BAY15D. Beacon 12V P21/5W.

from 56 rub. Fortluft (7528)

They burn out less often. I changed it only once in the right headlight. This is what she looks like:

How to replace headlight bulbs

1. First, remove the protective cover. It turns a little, then a small latch is released.

2. The block with wires is removed.

3. Remove the rubber protective sleeve.

4. The lamp is pressed U -shaped clamp. It needs to be pulled to the side and back.

5. Take out the lamp. Remember its orientation. Two teeth at the bottom, one at the top. And if you look at it from the side of the headlight, the inscription (marking) will be on top.

6. Install a new lamp. You should not take it with your bare hands, as greasy marks from the pores will remain on the bulb and the lamp will fail faster. This applies to all halogen lamps. It is better to hold it by the plinth or use a microfiber cloth.

7. Assembly is carried out in reverse order. First the clamping clamp, then the rubber bushing and finally the top cover.

How to replace front markers

There isn't much action here. The main thing is to get to the cartridge and turn it 90 degrees. On the left headlight it is clockwise, on the right it is counterclockwise. The most inconvenient thing to change is the battery side. Not enough space. If your hand is large, it is better to remove it.

If you can’t feel the cartridge at all, then the operating instructions advise removing the fender liner.

The procedure is as follows:

• Found a cartridge
• They turned it over and took it out
• Removed the lamp
• When installing a new lamp into the socket, it is better to wear gloves
• Then the cartridge was installed back into the headlight and rotated 90 degrees.

How to replace rear lights

Changing lamps is a pleasure. All you need to do is remove the headlight unit. It is secured with two wings from the interior: one at the top under the plastic upholstery, the other at the bottom. We unscrew them, move the headlight to the side and disconnect the block with the wires.

Next you need to remove the protective cover. It is held on by three latches. There are three lamps underneath it. We find the size lamp and change it. The steps are simple: insert into the cartridge and turn.

Side light circuit

It's very easy to replace the side light bulb yourself.

In order to save fuel and reduce the load on the generator, daytime running lights are now often included in this circuit, which makes it quite complicated.

The standard wiring option is quite simple and consists of the following elements:

• circuit breakers;
• front and rear position lamps;
• central or key switch;
• Let's take a closer look at the first two elements.

Read more: The engine number has been filed off, how to register it

Circuit breakers

Sometimes blown fuses are the reason why the side lights do not light up on one side or another.

There are usually two fuses in the circuit, for the left and right sides separately. Since the light bulbs consume little power (4-5 W each), the fuse rating is small, only 5-7.5 A.

Where are the side light fuses located?

In the same place as the others, in a single block. On most modern cars, this block is located under the instrument panel next to the steering column, or, more often, on the lower left, under a plastic trim.

In the latter case, it is enough to remove the cover protecting the unit, mounted on latches. On the back of the cover, as a rule, there is a sticker with information about which circuit this or that fuse protects, indicating its rating.

The biggest inconvenience in this case may be insufficient knowledge of the English language - it is in this language that inscriptions are usually made, even on Korean and Japanese cars.

Lamps

Externally, the headlight bulb is marked W5W, but today LED sidelight bulbs are increasingly used.

Their advantage over incandescent lamps is their greater durability, and the price of both largely depends on the manufacturer. The most famous products are Philips, Osram, Tesla.

Watch the video about LED bulbs for side lights:

Moreover, as the “Behind the Wheel” test showed, expensive products do not always justify their price.

Also, quite often, the front dimensions are equipped with light bulbs with a metal base, but this, one might say, is a thing of the past.

For rear position lights, the most common lamp is with two spirals - 21 and 5 (or 4) W.

The 21 W coil lights up when you press the brake, i.e. In this case, the light bulb serves as a brake light, while the lower power spiral works as a side light.

Just as with any other lamps, purchasing a more expensive product does not guarantee any exceptional durability.

Replacing lamps in the headlight (low and high beam lamps, front dimensions, turn indicator)

The procedure for replacing the right and left headlight bulbs is the same.

Location of lamps in the headlight: 1 – turn signal lamp; 2 – headlight adjustment mechanism; 3 – screw for adjusting headlights vertically; 4 – headlight lamp (low, high); 5 – side light lamp; 6 – horizontal headlight adjustment knob

Open the hood and disconnect the negative battery.

Replacing the head lamp (low and high beam)

Headlight bulb H4 - halogen, double-filament.

Turn the plastic cover, press the lock and remove it (in the photo, for clarity, the headlight is pulled out of the cavity in the body)

After releasing the lock, remove the wiring block from the lamp.

Lift the edge of the rubber sealing boot and remove it from the headlight.

By pressing the spring clamp of the lamp, disengage it from the reflector

And remove the headlight bulb (low and high beam) from the headlight housing

Insert the new lamp, secure it with the spring holder, install the rubber seal, attach the wiring block to it and replace the plastic cover.

Replacing the turn signal lamp

Turn signal lamp PY21W (orange).

Replacing the turn signal lamp in the headlight without removing the fender liner or battery can be problematic due to difficult access. Some drivers are able to do this, some are not. If you cannot make a replacement with direct access, proceed as follows:

Ford Explorer interior

Now you should inspect the interior. We sit behind the wheel to feel all the softness of the leather seats, which immediately remind us of the American origin of this car. I can't help but be pleased with the ability to adjust the driver's seat in ten directions, and the electric adjustments are equipped with memory. All this is done, of course, for the convenience of the driver.

The steering wheel is four-spoke. It is covered in leather, the color of which successfully harmonizes with the color of the entire interior. On the steering wheel there are control buttons for climate control, cruise control, and audio system. The only minor drawback of the steering wheel is that it is only adjustable in height. Also, the disadvantages of the interior include insufficient support for the seats on the sides, which, of course, affects the driver when making sharp turns.

It is impossible not to note the convenient and elegant dashboard, which is equipped with white dials that are easy to read. And here a little surprise awaits us: the speedometer contains additional markings in miles. Right! The Ford Explorer reminds drivers of its true roots.

The ergonomics of the driver's seat are excellent, except for the left steering column switch, which is not very convenient to operate due to its obvious functional overload: it is responsible for the direction indicators, the windshield wipers, and the light control. Thus, the interior leaves a pleasant impression, since it is made of high-quality leather and plastic, which, in fact, was not at all typical for earlier models of American cars. On the other hand, modern American models are increasingly equipped with similar high-quality material.

We are pleased with the updated center console, which is equipped with wooden inserts. It houses the climate control and audio system control unit. In addition, this is where the control buttons for the on-board computer and differential locks are located.

The button for opening the electric sunroof is conveniently located above the automatic selector knob on the ceiling. It is noteworthy that if you fold the third row seats, you can get a perfectly flat trunk floor.

If you go further and fold the Ford Explorer and the second row of seats into the car, the trunk becomes so voluminous and capacious that you can stuff an entire refrigerator into it. For the convenience of storing small and light items in the trunk, there is an interesting function. You can open the rear window separately using the button located on the ignition key!

To watch online, click on the video ⤵

Replacing the side light bulb of the front headlight of Lada Largus More details

How to replace side lamps on Lada Largus. Normal people. More details

Replacing a marker lamp in Largus Read more

Replacing headlight bulbs for Renault Logan, Lada Largus More details

Replacing front headlight bulbs on Renault Logan. More details

Installation and replacement of light bulbs in Largus headlights Read more

Replacing the light bulb in the rear light on a Lada Largus. More details

Replacing a light bulb on a Largus. More details

Replacing low and high beam lamps for Renault Logan and Lada Largus More details

Repair of Largus - Replacing the H4 lamp in the headlights on a LADA Largus (practice) More details

Replacing a Lada Largus light bulb Lada Largus More details

Auto electrician Nizhny Tagil. Largus illumination of the stove and buttons. Vingroad pillow. More details

Secret menu of the standard radio for Largus, Logan, Duster, Sandero Read more

DRL on LADA Largus with your own hands for 3 rubles 50 kopecks Read more

Self-diagnosis mode of the instrument panel for Renault Logan and Lada Largus Read more

Free auto electrician. Lada Largus stove blows cold. Replacing the marker lamp and license plate light. More details

Super bright reverse gear PROBRIGHT RL Omega in Lada Largus More details

Replacing fog lamps on Lada Largus Read more

Replacing side light bulbs on Lada Largus

From time to time, replacing a Lada Largus lamp becomes one of the mandatory procedures. The reason for this is that it becomes unusable, which in the dark is not only uncomfortable, but also life-threatening.

Timely replacement of lighting bulbs is the key to comfort and safety on the road

Of course, the service life of this lighting element directly depends on its quality and varieties. Although the terms of use are also important here. Indeed, with constant shaking while driving, it will often be necessary to replace not only the low beam lamp on the Lada Largus, but also the dimensions, brake lights and high beams.

Lighting elements of Lada Largus

It is worth noting that all lamps used in headlight lighting of Lada Largus cars are divided into three types:

The most common type of headlights for low or high beam are LED variations, since these are the most powerful and efficient lamps in terms of energy conservation. In addition, they can be used for brake lights, turn signals or markers.

What to choose for replacement

The standard factory installation is a halogen H4 light bulb on Largus. However, the modern car market offers alternative options for daytime car optics. There are three analogues:

Xenon ones have a bluish glow, which is inconvenient in cloudy or rainy-snowy weather. Halogen units shine brightly and warmly. They are a common installation option, although they are inferior in power to other analogues. The advantage of LED elements is that they can store energy for a long time at high power.

Standard replacement procedure

1. Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply. This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
2. The place where the Largus lamp will be replaced is determined. There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
3. Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
4. After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
5. If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
6. At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

When is the replacement made?

Vehicle manufacturers do not provide clear regulations for carrying out this work. There are only 3 reasons why car enthusiasts change their side light bulbs to new ones as needed:

1. The light elements have failed - they have burned out or gone out due to external mechanical influence.
2. The owner of the car decided to install more modern LED bulbs.
3. The lights began to shine too dimly.

The first reason is clear and does not require explanation. Installing LEDs is a useful operation, since these elements shine well, last a long time and consume much less electricity. The main thing is to maintain the polarity of the contacts during the replacement process, otherwise the new light bulb may fail or the fuses will begin to blow.

Stop signal

The principle of replacement is similar to the installation of the above-mentioned lamps, but it has its own nuances. Here, first, the trunk lid is opened and its decorative panel is removed. So, in order to replace the brake light, you must first of all clear the approach to the wing nuts.

After removing them, the entire headlight is turned out, which would be very problematic to do on your own. After all, you need to bring out its upper and lower parts at the same time so that they do not become a surprise. After unscrewing the screws, access to the lamp is open. The failed part is replaced, and all the previously listed steps are performed in the reverse order.

Dimensions

A special feature of this procedure is the preliminary dismantling of the headlight unit, under which the side light lamps are located. After this, it is necessary to disconnect the wires from the battery, which is done with extreme care.

Removing the front bumper will allow you to get to the cover that protects the dimensions. Since they come into contact with other light devices, it is advisable to carry out all procedures using sterile gloves. If any device has been touched, it must be wiped with a clean, lint-free cloth.

To replace the side light bulb in Largus, the socket of the old part is turned counterclockwise. The black and yellow wires connect it to the battery, so it turns off from them. A new part is installed in this place, and assembly is carried out in the reverse order.

Conclusion

You need to make it a rule to regularly change not only the lamps, but also monitor other lighting elements. After all, the process of reducing their brightness occurs slowly and the driver simply does not notice the deterioration in road lighting.

The side lamps for a Lada Largus car are very dim bulbs, so after they burn out or even without waiting for it, you can replace the side lamps with LED ones! The LED light bulb is very bright and economical! The price is for 1 piece. T-10 lamp socket. Also, this light bulb can be installed in the ceiling lamp, in the glove box, trunk lamp, room lighting, wherever the T10 socket is used.

During operation, observant owners of the universal LADA Largus model noticed frequent failure of low beam lamps in the head optics. This places this unit in the category of short-lived components and therefore requires replacement of the low beam lamp. The manufacturer is aware of the presence of this defect and is making promises to eliminate it as soon as possible. While this is being done, owners need to have knowledge of how to replace the low beam lamp themselves.

How to choose a lighting element?

The standard version of the configuration provides for the use of halogen lamps with an H4 base. This device contains two threads, each of which is responsible for its own light (naturally, near and far). Today's auto accessories market is able to offer its customers several analogue lamp options, structurally based on the following technologies:

Advice! When choosing lamps for your LADA Largus, lean towards the offers of specialized trading entities. The market is full of cheap analogues with Chinese ancestry. They cannot boast of reliability, and the effectiveness of such products is negligible. A useful point here would be to take into account the light characteristics of the lamp.

The most efficient lighting components are diode products. They can be installed not only as low or high beam devices, but also as marker optics or turn signals.

Note that an important advantage of a lamp using diode technology is its high ability to save energy. This factor is directly dependent on the manufacturer and the quality aspects of the product.

Important! During replacement, we remember their location, which will prevent incorrect installation and the need to repeat this manipulation.

How to replace the lamp?

Replacing a low beam lamp in a LADA Largus is not a complex procedure, which is quite feasible for inexperienced owners. Here you will need a simple set of tools. The right headlight will cause some difficulties, since the battery is located nearby. In general, this point can be easily eliminated. We will tell you how to change the lamp.

The lamp responsible for low beam in the Lada Largus has a rubber protective cover. This element can be easily moved to the side using manual force. This is done simultaneously with the removal of the power supply wire block.

The sequence of actions is as follows:

1. We turn off the power to the on-board network by removing the terminals from the battery or turning the switch, which is structurally present in the Lada Largus. This mandatory action implies ensuring electrical safety during the full range of manipulations.
2. We remove the rubber pad that covers the electrical component.
3. Now carefully move aside the pair of metal antennae that hold the lamp in the socket.
4. We disconnect the cable plugs with which the lamp is connected to the on-board network.
5. We mount the new lamp in the designated socket and securely fix it.
6. We connect the cable block to the electrical network.
7. Finally, we return the rubber protective plug to its original place.
8. We install all other previously removed components in their original places. Now you know how to change lamps.

Upon completion of the entire list of manipulations, we are sure to check the correct functioning of the entire set of lighting fixtures, including if the bulb dimensions were replaced.

Important! If suddenly, when checking, the lamps began to emit a dim luminous flux, or the side lights switched to flashing mode, then this indicates insufficient contact with the body. The reasons may include both dirt and ordinary oxidation, and it is not always necessary to replace the size bulb.

How to install fog lights?

Before starting the procedure for installing a set of fog lights in the Lada Largus bumper, we carry out a number of preparatory manipulations related to preliminary checking the correct connection of the wires and the functionality of the products, and also stock up on the necessary tools, the set of which is very simple.

The installation procedure is simple, so we can safely proceed to its implementation.

We open the hood and de-energize the network by removing the terminals from the battery. Now you can remove the front bumper, which will allow you to correctly install and connect the fog lights, as well as secure the wiring. We unscrew the screws from below that hold this element to the body of the LADA Largus. We do the same with the bolts under the hood and the screws in the wheel arches

We pay special attention to the two bolts hidden in the corners of the bumper, since without their “surrender” it will not succumb to removal, because the wings will not “set it free”. To defeat these fastening components we will use a screwdriver. During manipulation, carefully move the fender liner so that it does not interfere with our actions

We remove the bumper carefully, pulling it straight forward (in the direction of travel). Next, having conveniently positioned the bodywork, we dismantle the plugs. On the inner surface of the bumper we unhook the fixing components, after which the plugs are easily removed. We place new PTFs in the bumper niches and begin to securely fasten them. This is done using screws with which we fasten the lighting devices to the body element. Now we lay the wiring along the inner cavity of the bumper and fix it with tape and clamps. We do this on both sides of the body element. We fasten the negative wires to the body, which acts as the “ground” of the Lada Largus car. We install the bumper and secure it with the specified list of fasteners, proceeding in the reverse order. Next, you will need to bring the end sections of the PTF wires into the engine compartment area. When laying, we also use fastening ties. We move into the cabin and select a place to attach the pre-purchased PTF power button. The button itself can be embedded into the desired area of ​​the panel, which will be more aesthetically pleasing compared to fixing it on the surface of the interior element. The ends of the wiring attached to the button terminals are directed to the mounting block with relays and fuses. Remembering the cable ends of the PTF, we also bring them to the area where the unit is located, which is located on the left side of the steering column. We act according to the instructions included with the optics kit. We carry out all switching manipulations, connecting the wires as indicated in the instruction diagram. Finally, we check the functionality of the new lighting devices and, if necessary, adjust the correct direction of the light beam.