✅ How to change the side light bulb on a Largus video

What kind of bulbs are in the headlights?

Low and high beam lamp - H4, power 12V, 60/55W;
Bulb dimensions - W5W, power 5W;
Front turn signal lamp - PY21W;
Fog lamps - H11, power 12V, 55W.

How to change headlights on a Lada-Largus

Lada Largus is a popular family multi-purpose station wagon, mass production of which was launched by AvtoVAZ PJSC in 2012.

A car of this class is designed to meet the most diverse needs of potential buyers and can be used for both everyday and long-distance trips. At the same time, it feels great in urban conditions and on country roads.

The universal use of this car quite often contributes to damage to the elements of the front optics by stones flying from under the wheels of oncoming or passing vehicles, branches of low-growing bushes, etc.

Replacing damaged head optics and installing new elements is not difficult and can be carried out by almost any car owner, even those without experience in carrying out such work. The only difficulty with this is the need to dismantle the front bumper, where not only fog lights are integrated, but also headlights.

Block lights

Structurally, each block headlight of the LADA Largus station wagon consists of two sections. One contains:

"marker" lamp (W5W).
double-filament lamp for low and high beam (type H4);

Nearby is the section in which the PY21W turn signal lamp is located.

The headlight unit is dismantled when it is damaged or needs to be modified (tuning).

Replacing the headlight

Before you begin work related to replacing the headlight, you must:

Secure the station wagon using the handbrake.
Remove the key from the ignition.
Remove the negative wire from the battery terminal.

The dismantling of the headlight block of the LADA Largus station wagon begins by first removing the front bumper. This operation is shown in detail on the video page:

After this, access to the fastening elements in the lower part of the case will open. Next, you need to disconnect the electrical wires:

going to the H4 type lamp. To do this, remove the cover 3 and disconnect the pads;
remove the sockets for the direction indicator lamps 5 and indicator lamps 7;
remove the actuator of the headlight hydraulic corrector (if equipped) from the headlight housing, to do this, slide boot 4 along the cable and unclip the fastening latch.

after this, you need to unscrew the fastening bolts (items 1, 3 and 4) located around the perimeter of the body part (2);

push the headlight housing forward a little and remove it.

The new headlight unit is installed in the reverse order, maintaining a uniform gap between housing 2 and body parts.

Adjusting the luminous flux

After carrying out any work related to the head optics of the LALA Largus car, it is mandatory to check and adjust (if necessary) the direction of the luminous flux of the switched on lamps. To do this, it is best to contact a specialized service station, equipped with special instruments and staffed by qualified specialists. However, in case of emergency, such an operation can be carried out independently and without the necessary equipment. In practice, there are several ways to check and adjust headlights. You can see one of them by watching the video:

Low and high beam

One lamp is responsible for low and high beam. Its resource is 2000-4000 hours. To gain access to the left headlight unit, you must remove the battery.

Turn the lid counterclockwise;
Remove the cover by releasing the latch.

Remove the block with wires by unclipping the lock;
Remove the rubber cover by prying it off by the edge.

Unscrew the lamp clamp to the side;
Remove the headlight bulb.

Installing a new lamp in the Largus headlight is carried out in the reverse order. You need to hold the lamp by the base; it is not recommended to touch the bulb with your fingers. If necessary, wipe the flask with a microfiber cloth that does not leave lint. The process of replacing the H4 lamp is also shown in the video:

Lada Largus replacing lamps in the headlight unit magazine Behind the Wheel

Replacing the headlight bulb

2163-11-02-02-01

Remove the plastic cover (for clarity, the headlight mounting bolts are unscrewed and it is pushed forward).

Disconnect the wire block from the headlight lamp.

2163-11-02-02-03

Remove the rubber sealing cover (shown on the removed headlight for clarity).

2163-11-02-02-04

By pressing the spring clamp of the lamp, we remove it from engagement with the reflector hook.

2163-11-02-02-06

...and remove the headlight bulb from the headlight housing.

Attention! The headlight lamp is halogen. Do not touch its glass bulb, as fingerprints will cause the lamp to darken when heated. You can remove dirt from the flask with a clean rag soaked in alcohol.

You can remove dirt from the flask with a clean rag soaked in alcohol.

Install the new H4 headlight bulb in the reverse order.

Replacing the turn signal lamp

We release the clamp of the wire block...

2163-5-13-12-04

...and disconnect the block from the turn signal lamp socket.

2163-5-13-12-05

Turn the lamp socket clockwise (for the right headlight - counterclockwise) and remove the socket together with the lamp.

2163-5-13-12-07

By pressing the lamp, turn it counterclockwise and remove it from the socket.

We replace the burnt-out PY21W turn signal lamp with a new one.

Replacing the side light bulb

Before replacing the side light bulb, it is more convenient to first disconnect the wire block from the turn signal lamp socket (see above).

2163-5-13-12-01

Turn the side light bulb socket clockwise (for the right headlight - counterclockwise)...

2163-5-13-12-02

...and remove the lamp socket from the headlight housing.

We remove the baseless W5W side light lamp from the socket and replace it with a new one.

[Maintenance of Lada Largus at 15,000/45,000/75,000/105,000 km]

Error in the text? Select it with your mouse! And press: Ctrl + Enter

PTF lamp (fog lamp)

There is no access to the lamp from the engine compartment, so replacement is made from below.

Remove the fender liner by removing the screws;
Disconnect the block from the lamp by pressing the lock;
Remove the lamp by turning it a third of a turn counterclockwise.

Install the lamp in the reverse order.

Attention! In practice, replacing lamps in a Largus headlight is much easier. In other words, it is not at all necessary to remove the battery and fender liners (lockers). If you get the hang of it, you can access all the headlight bulbs from the engine compartment.

Let us remind you that other operating and repair instructions for Lada Largus are in this category. It is convenient to find the answer to your question based on the content.

How to change the low/high beam lamps on Largus, as well as the dimensions

A note about what kind of lighting lamps are installed in the Largus headlights; which of them are low/high beam, and which are responsible for the side lights. How to change lamps yourself. How much do originals and analogues cost in Yaroslavl?

Good day, future and aspiring gentlemen Largusovod!

On Largus, the low/high beam and headlight lamps often burn out. At least for 70 thousand I have already changed it five times on each side.

The following light bulbs were installed on my car:

1. Low/high beam: halogen, Osram H4 12v 60/55w. (art. 64193). Price from 109 rub.

There are many analogues. Here are some of them:

370 rub. General Electric (34454)

117 rub. Valeo (032007)

2. Front dimensions: halogen baseless 12V Osram (art. 2825). Price from 17 rub.

26 rub. Lynx (L12805)

9 rub. Fortluft (2825)

3. Rear dimensions: two-pin with filament, base BAY15D. Beacon 12V P21/5W.

from 56 rub. Fortluft (7528)

They burn out less often. I changed it only once in the right headlight. This is what she looks like:

How to replace headlight bulbs

1. First, remove the protective cover. It turns a little, then a small latch is released.

2. The block with wires is removed.

3. Remove the rubber protective sleeve.

4. The lamp is pressed U -shaped clamp. It needs to be pulled to the side and back.

5. Take out the lamp. Remember its orientation. Two teeth at the bottom, one at the top. And if you look at it from the side of the headlight, the inscription (marking) will be on top.

6. Install a new lamp. You should not take it with your bare hands, as greasy marks from the pores will remain on the bulb and the lamp will fail faster. This applies to all halogen lamps. It is better to hold it by the plinth or use a microfiber cloth.

7. Assembly is carried out in reverse order. First the clamping clamp, then the rubber bushing and finally the top cover.

How to replace front markers

There isn't much action here. The main thing is to get to the cartridge and turn it 90 degrees. On the left headlight it is clockwise, on the right it is counterclockwise. The most inconvenient thing to change is the battery side. Not enough space. If your hand is large, it is better to remove it.

If you can’t feel the cartridge at all, then the operating instructions advise removing the fender liner.

The procedure is as follows:

Found a cartridge
They turned it over and took it out
Removed the lamp
When installing a new lamp into the socket, it is better to wear gloves
Then the cartridge was installed back into the headlight and rotated 90 degrees.

How to replace rear lights

Changing lamps is a pleasure. All you need to do is remove the headlight unit. It is secured with two wings from the interior: one at the top under the plastic upholstery, the other at the bottom. We unscrew them, move the headlight to the side and disconnect the block with the wires.

Next you need to remove the protective cover. It is held on by three latches. There are three lamps underneath it. We find the size lamp and change it. The steps are simple: insert into the cartridge and turn.

Block lights

Structurally, each block headlight of the LADA Largus station wagon consists of two sections. One contains:

"marker" lamp (W5W).
double-filament lamp for low and high beam (type H4);

Nearby is the section in which the PY21W turn signal lamp is located.

The headlight unit is dismantled when it is damaged or needs to be modified (tuning).

Replacing the headlight

Before you begin work related to replacing the headlight, you must:

Secure the station wagon using the handbrake.
Remove the key from the ignition.
Remove the negative wire from the battery terminal.

The dismantling of the headlight block of the LADA Largus station wagon begins by first removing the front bumper. This operation is shown in detail on the video page:

Read more: Front strut liners for VAZ 2110

After this, access to the fastening elements in the lower part of the case will open. Next, you need to disconnect the electrical wires:

going to the H4 type lamp. To do this, remove the cover 3 and disconnect the pads;
remove the sockets for the direction indicator lamps 5 and indicator lamps 7;
remove the actuator of the headlight hydraulic corrector (if equipped) from the headlight housing, to do this, slide boot 4 along the cable and unclip the fastening latch.

after this, you need to unscrew the fastening bolts (items 1, 3 and 4) located around the perimeter of the body part (2);

push the headlight housing forward a little and remove it.

The new headlight unit is installed in the reverse order, maintaining a uniform gap between housing 2 and body parts.

Adjusting the luminous flux

Replacing lamps in a headlight

Among the sudden malfunctions that almost all car owners encounter, one of the first places is the failure of head optics light sources. These include lamps:

low/high beam;
direction indicator;
Dimensions indicator.

All of them are located inside a separate headlight and changing them, if necessary, is not difficult.

Replacing the low/high beam lamp

Change the low/high beam lamp in the LADA Largus headlight in the following order:

remove the protective cover;

disconnect the block with wires;

pull out the rubber seal;
pressing on the spring holder, remove it from under the latch;

Carefully releasing the holder, carefully remove the burnt out lamp.

The new lamp is inserted into the reflector hole and secured using standard fasteners. Then all the removed parts are returned to their places.

Attention! Lada Largus uses halogen light sources, the glass surface of which is not recommended to be touched. To avoid darkening of the flask when heated, it is recommended to hold them by the base.

Read more: UAZ installation of ignition by marks

Replacing the turn signal lamp

In order to change a faulty lamp installed in the turn signal compartment, you must:

gently press out the plastic connector retainer;

disconnect the connector with the on-board power supply wires;

remove the lamp socket from the headlight socket by turning it clockwise (left lamp) or counterclockwise (right lamp);

By pressing and turning the lamp counterclockwise, we take it out.

The new lamp is installed in the reverse order.

Replacing the indicator lamp

A burnt-out baseless bulb installed in the size indicator is changed as follows:

disconnect the block with electrical wires from the cartridge;
turn the socket clockwise (left lamp) or counterclockwise (right lamp) and remove it from the headlight housing;

A new lamp is placed in place of the burnt one.

The cartridge is returned to the standard socket, performing all operations in the reverse order.

Replacing lamps in the headlight (low and high beam lamps, front dimensions, turn indicator)

The procedure for replacing the right and left headlight bulbs is the same.

Location of lamps in the headlight: 1 – turn signal lamp; 2 – headlight adjustment mechanism; 3 – screw for adjusting headlights vertically; 4 – headlight lamp (low, high); 5 – side light lamp; 6 – horizontal headlight adjustment knob

Open the hood and disconnect the negative battery.

Replacing the head lamp (low and high beam)

Headlight bulb H4 - halogen, double-filament.

Turn the plastic cover, press the lock and remove it (in the photo, for clarity, the headlight is pulled out of the cavity in the body)

After releasing the lock, remove the wiring block from the lamp.

Lift the edge of the rubber sealing boot and remove it from the headlight.

By pressing the spring clamp of the lamp, disengage it from the reflector

And remove the headlight bulb (low and high beam) from the headlight housing

Insert the new lamp, secure it with the spring holder, install the rubber seal, attach the wiring block to it and replace the plastic cover.

Replacing the turn signal lamp

Turn signal lamp PY21W (orange).

Replacing the turn signal lamp in the headlight without removing the fender liner or battery can be problematic due to difficult access. Some drivers are able to do this, some are not. If you cannot make a replacement with direct access, proceed as follows:

Operations for removing the headlight unit Lada Largus

1. Disconnect the wire from the negative terminal of the battery. 2. Remove the front fender liner - the plastic arch protection.

3. Press out the clamp of the turn signal lamp socket wiring harness block. 4. . and disconnect the block from the cartridge

5. Turn the side light bulb socket clockwise (for the right headlight, counterclockwise). 6. . and remove it from the headlamp.

Read more: Types of diagnostic connectors for cars

7. Turn the plastic headlight cover 8. . release the cover lock. 9. . and remove the cover..

10. Press the clamp of the harness block 11. . and disconnect the block from the base

12. Remove the protective cover with the headlight corrector 13. Remove the corrector drive cable from the holder. 14. . and disconnect it from the headlight range control unit.

15. Remove the front bumper.

16. Remove the three lamp mounting bolts. block headlights to the radiator frame.

This is how the headlight mounting bolts are located. 17. . and remove the headlight unit.

18. Install the headlight in the reverse order of removal and check that the headlights are adjusted correctly.

Lada Largus is a popular family multi-purpose station wagon, mass production of which was launched by AvtoVAZ PJSC in 2012.

To watch online, click on the video ⤵

Replacing the side light bulb of the front headlight of Lada Largus More details

How to replace side lamps on Lada Largus. Normal people. More details

Replacing a marker lamp in Largus Read more

Replacing headlight bulbs for Renault Logan, Lada Largus More details

Replacing front headlight bulbs on Renault Logan. More details

Installation and replacement of light bulbs in Largus headlights Read more

Replacing the light bulb in the rear light on a Lada Largus. More details

Replacing a light bulb on a Largus. More details

Replacing low and high beam lamps for Renault Logan and Lada Largus More details

Repair of Largus - Replacing the H4 lamp in the headlights on a LADA Largus (practice) More details

Replacing a Lada Largus light bulb Lada Largus More details

Auto electrician Nizhny Tagil. Largus illumination of the stove and buttons. Vingroad pillow. More details

Secret menu of the standard radio for Largus, Logan, Duster, Sandero Read more

DRL on LADA Largus with your own hands for 3 rubles 50 kopecks Read more

Self-diagnosis mode of the instrument panel for Renault Logan and Lada Largus Read more

Free auto electrician. Lada Largus stove blows cold. Replacing the marker lamp and license plate light. More details

Super bright reverse gear PROBRIGHT RL Omega in Lada Largus More details

Replacing fog lamps on Lada Largus Read more

Replacing headlight bulbs for Lada Largus

Car headlights are designed to provide a full view of the road at night. The proper condition of all lighting sources on the car is a necessary condition for safety while driving. Traffic regulations set very strict requirements for the serviceability of headlights. A driver who does not comply with them is subject to a fine.

To avoid troubles with the car inspection, the car owner is obliged to regularly inspect the lights on his car and, if defects or breakdowns are detected, promptly take measures to eliminate them.

Keeping your headlights on at night can save your life.

Headlights on Lada Largus may have the following types of problems:

burnt out lamps;
broken lamps;
cracks on the surface of the optics;
dimming of lights;
incorrect formation of the light beam, etc.

The reasons for these problems may vary. Clouding of the optics is caused by the matting effect of dust particles in the oncoming air flow; cracks and broken lamps are usually the result of a collision with an obstacle while driving. Scratches on the surface of the optics can be the result of driving on roads with bushes and trees with spreading branches growing on the sides.

Driving with headlights that have any of the above factors is unacceptable. To carry out repairs, you can contact a service station, where qualified technicians will provide you with the required assistance. But car service costs money - not all vehicle owners are ready to incur financial expenses.

Burnt out bulb H4

If you want to avoid spending money, try doing it yourself. On Lada Largus cars, replacing lamps and lights does not cause any particular difficulties. And use the information you glean from this article as a guide.

How to replace Mazda 3 low beam bulbs

Changing lamps

First, let's look at how to replace the low beam bulb and replace the high beam bulb on the Lada Largus. Headlights on Lada Largus use one H4 lamp with a voltage of 12 V and a power of 60/55 W for low and high beam. Therefore, replacing the low beam bulb on a Lada Largus will automatically mean replacing the high beam bulb.

While working, follow the following algorithm:

To access the left light, you will need to remove the battery.
Turn the lantern cover counterclockwise.
Release the holder and remove the cover.
Release another holder to remove the cable block.
Hook the rubber cap on the edge and open it.
Move the light bulb holder aside and remove it.

Replacing side light bulbs on Lada Largus

From time to time, replacing a Lada Largus lamp becomes one of the mandatory procedures. The reason for this is that it becomes unusable, which in the dark is not only uncomfortable, but also life-threatening.

Timely replacement of lighting bulbs is the key to comfort and safety on the road

Of course, the service life of this lighting element directly depends on its quality and varieties. Although the terms of use are also important here. Indeed, with constant shaking while driving, it will often be necessary to replace not only the low beam lamp on the Lada Largus, but also the dimensions, brake lights and high beams.

Replacing a low beam lamp on a Lada Largus

Once you have removed the lamp, you can begin replacing it:

hold the new lamp by the base;
To avoid touching the glass flask with bare hands, wear gloves. Why can't you touch the flask? Because traces of fat can lead to rapid burnout. If you need to wipe it down, don't use microfiber cloths;
secure the base with a spring clip;
Place the block on the contacts, and then install the plug in place.

Read

That's all. You have changed the lamp, and, as you can see, the process is simple.

When you replace one lamp, replace the second one immediately. You will avoid unexpected burnout and ensure an even glow.

Lighting elements of Lada Largus

It is worth noting that all lamps used in headlight lighting of Lada Largus cars are divided into three types:

The most common type of headlights for low or high beam are LED variations, since these are the most powerful and efficient lamps in terms of energy conservation. In addition, they can be used for brake lights, turn signals or markers.

Standard replacement procedure

Replacing the low beam lamp, as well as the high beam, begins by disconnecting the on-board power supply. This precedes all electrical repair work. In this case, a special switch is turned or the negative terminal is disconnected from the battery, which avoids accidental short circuits or erroneous connections during installation.
The place where the Largus lamp will be replaced is determined. There, the rubber plugs covering the electrical components are removed, and two metal antennae are opened in front of the car owner, fixing them in the reflector. They are separated so that the used parts can come out of their seat without damaging the housing.
Next, you need to disconnect the plugs from the wiring that was previously disconnected. Here it is worth paying attention to the order of arrangement, otherwise, during the installation of new parts, everything can be mixed up and they will have to be changed again.
After connecting the plug with wiring to the new parts, they are mounted in place and secured with antennae. You should try not to touch the flasks with your hands, as this can lead to their rapid failure.
If the light is dim during lighting, and the headlights flash when you turn on the headlights, then it is imperative to restore the contacts of the wires with the vehicle body. This is especially true for a marker lamp, because the fat that gets there begins to evaporate when heated and can cause ignition.
At the end of this procedure, you need to put on the rubber plugs and secure all the parts in their places. After this, the car will be ready for use and the driver does not have to worry about malfunctions of the Lada Largus lighting fixtures.

How to remove a low beam lamp

Removing the low beam lamp on the Lada Largus occurs as follows:

Disconnect the on-board power supply.
First, disconnect the terminals from the battery.
Then remove the plug from the back of the headlight. So that you can remove it, simply turn it slightly counterclockwise, releasing the lock.
Next, disconnect the block from the contacts. Simply pull it by the body and release the latch.
Remove the rubber cover by prying it off.
Remove the spring clip from the grooves.

Now there is nothing holding the lamp, and you can easily remove it.

Stop signal

The principle of replacement is similar to the installation of the above-mentioned lamps, but it has its own nuances. Here, first, the trunk lid is opened and its decorative panel is removed. So, in order to replace the brake light, you must first of all clear the approach to the wing nuts.

After removing them, the entire headlight is turned out, which would be very problematic to do on your own. After all, you need to bring out its upper and lower parts at the same time so that they do not become a surprise. After unscrewing the screws, access to the lamp is open. The failed part is replaced, and all the previously listed steps are performed in the reverse order.

Dimensions

A special feature of this procedure is the preliminary dismantling of the headlight unit, under which the side light lamps are located. After this, it is necessary to disconnect the wires from the battery, which is done with extreme care.

Removing the front bumper will allow you to get to the cover that protects the dimensions. Since they come into contact with other light devices, it is advisable to carry out all procedures using sterile gloves. If any device has been touched, it must be wiped with a clean, lint-free cloth.

To replace the side light bulb in Largus, the socket of the old part is turned counterclockwise. The black and yellow wires connect it to the battery, so it turns off from them. A new part is installed in this place, and assembly is carried out in the reverse order.

Conclusion

You need to make it a rule to regularly change not only the lamps, but also monitor other lighting elements. After all, the process of reducing their brightness occurs slowly and the driver simply does not notice the deterioration in road lighting.

The side lamps for a Lada Largus car are very dim bulbs, so after they burn out or even without waiting for it, you can replace the side lamps with LED ones! The LED light bulb is very bright and economical! The price is for 1 piece. T-10 lamp socket. Also, this light bulb can be installed in the ceiling lamp, in the glove box, trunk lamp, room lighting, wherever the T10 socket is used.

During operation, observant owners of the universal LADA Largus model noticed frequent failure of low beam lamps in the head optics. This places this unit in the category of short-lived components and therefore requires replacement of the low beam lamp. The manufacturer is aware of the presence of this defect and is making promises to eliminate it as soon as possible. While this is being done, owners need to have knowledge of how to replace the low beam lamp themselves.

How to choose a lighting element?

The standard version of the configuration provides for the use of halogen lamps with an H4 base. This device contains two threads, each of which is responsible for its own light (naturally, near and far). Today's auto accessories market is able to offer its customers several analogue lamp options, structurally based on the following technologies:

Advice! When choosing lamps for your LADA Largus, lean towards the offers of specialized trading entities. The market is full of cheap analogues with Chinese ancestry. They cannot boast of reliability, and the effectiveness of such products is negligible. A useful point here would be to take into account the light characteristics of the lamp.

The most efficient lighting components are diode products. They can be installed not only as low or high beam devices, but also as marker optics or turn signals.

Note that an important advantage of a lamp using diode technology is its high ability to save energy. This factor is directly dependent on the manufacturer and the quality aspects of the product.

Important! During replacement, we remember their location, which will prevent incorrect installation and the need to repeat this manipulation.

How to replace the lamp?

Replacing a low beam lamp in a LADA Largus is not a complex procedure, which is quite feasible for inexperienced owners. Here you will need a simple set of tools. The right headlight will cause some difficulties, since the battery is located nearby. In general, this point can be easily eliminated. We will tell you how to change the lamp.

The lamp responsible for low beam in the Lada Largus has a rubber protective cover. This element can be easily moved to the side using manual force. This is done simultaneously with the removal of the power supply wire block.

The sequence of actions is as follows:

We turn off the power to the on-board network by removing the terminals from the battery or turning the switch, which is structurally present in the Lada Largus. This mandatory action implies ensuring electrical safety during the full range of manipulations.
We remove the rubber pad that covers the electrical component.
Now carefully move aside the pair of metal antennae that hold the lamp in the socket.
We disconnect the cable plugs with which the lamp is connected to the on-board network.
We mount the new lamp in the designated socket and securely fix it.
We connect the cable block to the electrical network.
Finally, we return the rubber protective plug to its original place.
We install all other previously removed components in their original places. Now you know how to change lamps.

Upon completion of the entire list of manipulations, we are sure to check the correct functioning of the entire set of lighting fixtures, including if the bulb dimensions were replaced.

Important! If suddenly, when checking, the lamps began to emit a dim luminous flux, or the side lights switched to flashing mode, then this indicates insufficient contact with the body. The reasons may include both dirt and ordinary oxidation, and it is not always necessary to replace the size bulb.