Changing the oil in the Lada Largus engine 16 valves

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

Changing the oil in the Lada Largus engine is a common procedure for periodic vehicle maintenance, which is performed approximately every 15 thousand km. mileage (some drivers change it to 10). Any man can change the engine oil with his own hands—there’s nothing complicated about it.

Changing the oil in a Lada Largus (16 valves) involves removing the crankcase protection. Otherwise, you won’t be able to get to the oil filter, which also needs to be replaced. After removing the protection, you need to place a container for used oil, unscrew the drain plug, and drain the oil.

While he's running away, you can work on the oil filter. To remove it, you will need a puller . There are several types of oil filter pullers, but in this case the so-called “crab” is most suitable.

This video with instructions will allow you to see how to change the oil and oil filter on a Lada Largus.

The choice of oil for internal combustion engines should be given special attention, since the operation of your vehicle depends on its quality. Therefore, you need not only to replace it on time, but also to know what consumables to fill. Now you can find out which engine oil is suitable for Lada Largus and how to change it.

We change the oil ourselves

There is nothing scary about this process - even a person who has never driven a car can handle it. If you follow the steps and tips described in this material, you will be able to do everything correctly and your “iron horse” will be very grateful to you.

Which oil is suitable?

The choice of motor oil (hereinafter referred to as MM) for replacement in the 16 valve Lada Largus engine is the first difficulty faced by a car owner who decides to replace this consumable. We need to dwell on this point in more detail, since many Lada owners often make mistakes when choosing motor fluid.

Car Lada Largus

As mentioned above, the quality of this consumable material affects the operation of the engine, as well as the wear resistance of the elements of the internal combustion engine system. If the filled engine oil is of low quality or does not meet the vehicle manufacturer’s recommendations, then the service life of the machine is significantly reduced. In addition, if your car is relatively new and is under warranty, then if you operate a low-quality MM, you may simply be denied engine repair if necessary.

To find out exactly what consumables should be filled into the Lada Largus, you should read the service manual for your car. The necessary parameters and characteristics that the motor fluid must have are clearly indicated there.

In particular, for a 16-valve Largus engine, the manufacturer recommends using a MM that meets the following quality classes:

Where is the oil filter located?

The oil filter in the Lada Largus is located next to the crankcase and the drain plug. It is easy to recognize by its cylindrical case, which is predominantly blue. It can be unscrewed by hand, but if it is tightened too tightly, additional tools may be required.

In some assemblies, the location of the filter element may vary. To obtain the necessary information, refer to the technical documentation or find the oil filter yourself. Also, for easy access to it, additional steps may be required to dismantle the pipes and units.

Preparation for replacement and necessary tools

The process of preparing to replace the Largus oil filter includes three main points:

• purchase of new parts and consumables;
• parking the car on level ground;
• warming up the engine to operating temperature if it has not been running for a long time.

For convenience, it is recommended to use an overpass, inspection hole or lift. In the absence of the appropriate opportunity, the car is raised using a jack and supports.

When working with oil, pay attention to safety precautions . The main emphasis is on its high temperature and toxicity. To avoid thermal and chemical burns, the entire procedure should be performed with rubber gloves and overalls.

The list of tools for replacing the oil filter in Lada Largus consists of the following equipment :

• a set of keys and screwdrivers, a collar with attachments, a probe, pliers;
• clean, lint-free rags or rags, rubber gloves;
• container for draining used lubricant;
• new oil, funnel for filling;
• new oil filter, seals and gaskets, and other components to replace worn parts.

During the preparation process, it is also recommended to check the system for worn connections, which can soon lead to breakdowns and leaks. Preventative replacement of parts allows you to avoid costly repairs and unforeseen complications.

Step-by-step replacement instructions

The sequence of replacing the oil filter for Lada Largus implies the following procedure:

• in the engine compartment, uncork the filler neck;
• dismantle the lower engine protection;
• Place a container under the drain in the lower part of the crankcase and unscrew the plug;
• the heated lubricating fluid usually drains within 10-15 minutes;
• during this time, clean the plug, change the washer if necessary;
• They also place a container for used lubricant under the oil filter and unscrew it;
• remove the cartridge, make sure that the perforated tube remains in place, clean the internal cavity of the casing dry;
• the rubber seals of the new filter element are lubricated with oil, some also wash the filter itself;
• Next, the filter element is mounted in place, while tightening, monitor the position of the sealing rubber bands - if they come out of the grooves, a leak will soon appear;
• tighten the drain plug, return the system to its original form;
• New lubricant is poured into the filler neck.

Read more: Dimensions of Chery Tiggo fl radio

Based on the volume of oil poured, they are guided by the amount that was drained. Some experts recommend immediately filling it to the maximum, arguing that as the engine warms up, the oil will disperse throughout the system.

After filling, start the engine and let it run for 10-15 minutes. At first, the emergency light may come on, indicating a lack of oil in the system.

After warming up, measure the lubricant level - in the heated state, its amount should not exceed the upper permissible limit on the dipstick. If necessary, the excess is pumped out with a syringe or bulb.

It is also recommended to measure the oil level when the engine has cooled down - the volume should not be below the permissible minimum. After the first trips, it is recommended to check the system and oil filter for leaks.

In accordance with the maintenance regulations, the oil in the 16-valve Lada Largus engine, as well as the oil filter, should be changed every 15 thousand kilometers. The step-by-step instructions with photos below will help you cope with this task.

LADA > Largus

We carry out the work of changing the oil and oil filter in the 16-valve Lada Largus engine on an inspection ditch or overpass.

We carry out the replacement with the warm engine not running, preferably immediately after the trip, before the oil has cooled down.

Remove the oil filler cap.

How to drain engine oil

You will need : buy engine oil and an oil filter, prepare a “10” wrench, an “8” square wrench, a clean cloth, an empty 5 liter container. and a wire brush.

The engine oil should be drained after a trip while the engine is still warm (if necessary, warm it up to operating temperature). It is recommended to drive the car onto an overpass.

Procedure:

1. Unscrew the oil filler plug.
2. (At the bottom of the car on the engine crankcase), clean the drain plug with a wire brush, then unscrew it. Be careful not to burn yourself!
3. After all the oil has run out (about 10 minutes) into a previously placed container, clean the plug from dirt and screw it back.

Under the plug there is a steel washer on the surface of which a thin layer of rubber is vulcanized. If it is damaged, replace the washer with a new one. If you do not have a new washer, you can install a copper washer with a hole diameter of 18 mm under the plug.

All steps for changing oil on Largus “step by step”

Let's consider what to do before changing the oil in the Lada Largus engine if the number of valves is 16:

1. Warm up the engine, turn off the ignition, drive the car into the pit;
2. Remove the crankcase protection. You need a 10mm socket wrench - use it to unscrew the six screws from the bottom;

Fastening the crankcase protection

The protection is removed for one purpose - to get to the filter.

Draining waste (old engine oil)

There is no crankcase protection now. All that remains is to take the 8-sided socket and unscrew the drain plug.

Drain hole for plug

Make 1-2 turns with the key, then place an empty container and unscrew the cap by hand.

The time for draining used oil is at least 10 minutes. Be careful, the oil is hot!

After the waste has drained, the surface of the crankcase is wiped and the plug is wrapped. Thread tightening torque – 22 N*m.

Replacing the oil filter

It would seem that the old material has been drained and now is the time to complete the replacement. But you still need to change the oil filter.

Filter housing - put a puller on it

It is easier to access the filter housing from below. We take the puller and unscrew the filter by rotating the housing counterclockwise.

100-200 ml of waste will flow out of the old filter.

The new filter housing must be filled with oil, but not completely, but by a third. You will need 70-100 ml of material. The rubber seal is lubricated with the same oil.

Preparing the filter for installation

After wiping the engine crankcase, screw in the new filter until it stops. The tightening torque will be 15-17 N*m (by hand).

Pour in new oil

The oil volume in the Lada Largus engine, if the timing belt contains 16 valves, is 5 liters. You need to fill 4.8 liters through the neck. Then close the plug and start the engine.

The indicator light is now on

The point is to turn off the oil pressure light. We start, wait three minutes and turn off the engine.

Even if the control lamp did not light up, wait 5-6 minutes and check the level. The check is carried out using a dipstick, and you can find it near the power steering reservoir.

Read more: Cook oatmeal porridge with milk

Oil level dipstick

We remove the dipstick and look at the marks. If necessary, add oil. The main thing is to return the dipstick to its place, pressing it all the way.

The filler neck can also be used to pump out oil. Thin tubes and a bulb will help solve the problem.

How to fill engine oil

We pour new oil into the engine through the oil filler neck, the amount of oil in the engine is indicated in the table above. (about 0.3 liters of oil will still remain in the engine). We control the level using the oil dipstick (the oil level should be between the MIN and MAX marks).

Start the engine and let it idle for a few minutes. The emergency oil pressure indicator should go out 2-3 seconds after starting the engine. While the engine is running, check for oil leaks from under the drain plug and oil filter. Stop the engine and check the oil level; if necessary, add oil to the specified level.

The entire process of changing the Lada Largus oil is also shown in the video:

Signs of a clogged oil filter

The main purpose of the oil filter is to clean the circulating oil from impurities. They arise during the production of lubricating fluid, friction of mechanisms, and temperature changes.

A pressing issue for many car owners is identifying signs of the need for replacement . These usually include:

• extraneous sounds in engine operation, twitching, vibration;
• reduction in engine power, activation of the emergency light;
• change in lubricant color, appearance of sediment, burnt odor.

However, experts do not recommend waiting for such factors to manifest themselves. These signs already indicate malfunctions in the system and increased wear of parts. To prevent costly repairs, attention is paid to preventive measures and timely replacement of the lubricant and oil filter.

Read more: How to remove the lower arm of a Mazda 6

Regarding the operation of the filter itself, its throughput is emphasized. When worn, it decreases, which limits the supply of lubricant to the operating mechanisms of the engine.

Many car owners, instead of completely replacing the oil filter, clean it and return it to its place. This option is allowed as a temporary measure, however, for a long-term effect, the filter element must be changed along with the oil.

Replacement procedure

If a simple top-up is not enough, then you will need to perform a full oil change in the Largus gearbox. The procedure is not the most complicated, so it can be done on your own. The set of tools is similar. You just need to take a completely new container with lubricating fluid that meets the requirements of the Lada Largus gearbox. In the gearbox of Largus cars of the domestic Lada brand, when replacing the lubricant, oil of a certain marking is used, which meets factory requirements. If we talk about the volume of oil, it is approximately 3 liters.

When all the tools are at your disposal, prepare the car itself for the procedure. For this:

• install the machine over the pit or lift it using a lift;
• prepare a container of sufficient volume to drain all the old transmission fluid;
• get to the filler neck and unscrew its cap (this will allow the oil to drain out of the gearbox faster);
• find the drain hole and carefully unscrew the plug (you can’t do it by hand, use special pullers for oil filler plugs);
• when the lubricating fluid has completely drained into the prepared container, you can return the plugs to their place;
• there is a copper sealing ring on the drain hole, which should be changed after each procedure for updating the oil in the box (it gets pinched and therefore does not perform its functions well in the future);
• Having closed the drain hole, start gradually pouring fresh oil through the filler neck;
• the Largus box holds approximately 3 liters of transmission fluid, but due to residual old oil it can fit a little less;
• pour gradually until viscous liquid begins to flow out of the filler hole, which indicates that the gearbox is correctly filled;
• thoroughly wipe off all the oil with a rag and return the plug to its place;
• start the engine, work the gearshift knob to fully distribute the oil throughout the gearbox system.

Practice shows that changing gear oils in Largus does not require much experience or special knowledge. The procedure is carried out using a minimal set of tools and requires a short amount of time. Keep in mind that the plant recommends changing the lubricating fluid in the gearbox once every 200 thousand kilometers. But you need to build on the operating conditions and current state. 200 thousand kilometers is the period when the lubricating fluid loses its technical and chemical properties.