Design features, troubleshooting and replacement of the VAZ 2107 camshaft

Camshaft VAZ 2107

The camshaft is the main element of the gas distribution mechanism of a car engine. This is an all-metal part, made in the form of a cylinder with support journals and cams placed on it.

The camshaft contains cams and journals

Purpose

The timing shaft is used to control the processes of opening and closing valves in the combustion chambers of the engine. In other words, it synchronizes the operating strokes of the power unit, promptly admitting the fuel-air mixture into the combustion chambers and releasing exhaust gases from them. The camshaft of the “seven” is driven by the rotation of its star (gear), connected through a chain to the crankshaft gear.

Where is it located?

Depending on the design of the engine, the timing shaft may have a different location: upper and lower. With its lower location, it is installed directly in the cylinder block, and with its upper location, it is installed in the cylinder head. For "sevens" the camshaft is located in the upper part of the cylinder head. This arrangement, first of all, makes it easily accessible for repair or replacement, as well as for adjusting valve clearances. In order to get to the timing shaft, just remove the valve cover.

Operating principle

As mentioned, the camshaft is driven by the crankshaft gear. At the same time, its rotation speed, due to the different sizes of the drive gears, is reduced exactly by half. The full operating cycle of the engine occurs in two revolutions of the crankshaft, but the timing shaft makes only one revolution, during which it manages to let the fuel-air mixture into the cylinders one by one and release the exhaust gases.

The opening (closing) of the corresponding valves is ensured by the action of the cams on the valve tappets. It looks something like this. When the shaft rotates, the cam with its protruding side presses the pusher, which transmits force to the spring-loaded valve. The latter opens a window for the intake of the combustible mixture (exhaust of gases). As the cam rotates further, the valve closes under the action of a spring.

The valves open when the protruding parts of the cams press on them

Characteristics of the VAZ 2107 camshaft

The operation of the VAZ 2107 timing shaft is determined by three main parameters:

• phase width - 232o;
• intake valve lag - 40°;
• exhaust valve advance - 42o.

The number of cams on the camshaft corresponds to the number of intake and exhaust valves. The "seven" has eight of them - two for each of the four cylinders.

Find out more about the operation of the timing belt: https://bumper.guru/klassicheskie-modeli-vaz/grm/grm-2107/metki-grm-vaz-2107-inzhektor.html

Purpose and principle of operation

The camshaft is a metal rod on the axis of which eight cams are placed. These are parts that have an irregular shape. They rotate on the axis of the camshaft and are located opposite the inlet valves of the cylinders. Their rotation ensures stable combustion of the fuel mixture inside the cylinders. All these mechanisms are brought into precise synchronization.

Thanks to the proper operation of the shaft, a mixture of air and fuel is released into the cylinders in a timely manner, compression and release of exhaust gases occurs. On the Classic, the camshaft is driven by the fact that its gear rotates as a result of interaction with the crankshaft sprocket through a chain.

On the VAZ 2107, the camshaft is located at the top above the cylinder block. Thanks to this, it is available for self-replacement. This also makes it possible to easily adjust valve clearances.

To better understand the principle of operation of the camshaft, watch the video tutorial.

Is it possible to increase the power of a VAZ 2107 engine by installing a different camshaft?

Probably, every owner of the “Seven” wants the engine of his car to work not only without interruptions, but also with maximum efficiency. Therefore, some craftsmen are trying to tune power units using various methods. One of these methods is to install a different, more “advanced” camshaft.

The essence of tuning

Theoretically, it is possible to increase the power performance of a power unit by increasing the phase width and lift height of the intake valve. The first indicator determines the period of time during which the intake valve will be open, and is expressed in the angle of rotation of the timing shaft. For the “seven” it is 232o. The lift height of the intake valve determines the area of ​​the hole through which the fuel-air mixture will be supplied to the combustion chamber. For VAZ 2107 it is 9.5 mm. Thus, again, in theory, as these indicators increase, we get a larger volume of combustible mixture in the cylinders, which can really have a positive effect on the power of the power unit.

The phase width and lift height of the intake valve can be increased by changing the configuration of the corresponding cams of the gas distribution shaft. Since such work cannot be done in a garage, for such tuning it is better to use a finished part from another car.

Camshaft from Niva

There is only one car whose camshaft is suitable for the “seven”. This is a VAZ 21213 Niva. Its timing shaft has a phase width of 283°, and the intake valve lift is 10.7 mm. Will installing such a part on a VAZ 2107 engine give anything in reality? Practice shows that yes, there is a slight improvement in the operation of the power unit. The power increase is approximately 2 liters. s., but only at low revs. Yes, the “seven” responds a little sharper to pressing the accelerator pedal at the start, but once it gains speed, its power becomes the same.

Sports camshafts

In addition to the timing shaft from Niva, the VAZ 2107 can also be equipped with one of the shafts made specifically for “sports” tuning of power units. Such parts are produced by a number of domestic enterprises. Their cost ranges from 4,000–10,000 rubles. Let's look at the characteristics of such camshafts.

Table: main characteristics of “sports” timing shafts for VAZ 2101–2107

Malfunctions of the VAZ 2107 camshaft, their symptoms and causes

Considering that the timing shaft is subject to constant dynamic and temperature loads, it cannot last forever. It is difficult even for a specialist to determine that this particular unit has failed without detailed diagnostics and troubleshooting. There may be only two signs of its malfunction: a decrease in power and a quiet knocking sound, which manifests itself mainly under load.

The main camshaft faults include:

• wear of the working bodies of the cams;
• wear of the surfaces of the bearing journals;
• deformation of the entire part;
• shaft fracture.

More about timing chain repair: https://bumper.guru/klassicheskie-modeli-vaz/grm/grm-2107/kak-natyanut-tsep-na-vaz-2107.html

Wear of cams and journals

Wear is a natural occurrence for a constantly rotating part, but in some cases it can be excessive and premature. This leads to:

• insufficient oil pressure in the system, as a result of which lubricant does not flow to loaded areas or is supplied in smaller quantities;
• low-quality motor oil or one that does not meet established requirements;
• defect in the production of the shaft or its “bed”.

If the cams wear out, the engine power is noticeably reduced, since they, being worn out, cannot provide either the appropriate phase width or the required lift of the intake valve.

When the cams wear out, engine power drops

Deformation

Camshaft deformation occurs as a result of severe overheating caused by malfunctions of the lubrication or cooling systems. At the initial stage, this malfunction may manifest itself in the form of a characteristic knocking sound. If you suspect such a breakdown, further operation of the car is not recommended, as it can damage the entire gas distribution mechanism of the engine.

Deformation occurs due to malfunctions in the lubrication and cooling systems

Fracture

A camshaft fracture may be a consequence of its deformation, as well as poor timing. In the event of this malfunction, engine operation stops. In parallel with this problem, others arise: destruction of the shaft “bed”, bending of valves, guides, damage to parts of the piston group.

A shaft fracture may be a consequence of deformation

Troubleshooting the VAZ 2107 timing shaft

When the camshaft is removed from the “bed”, it is necessary to assess its condition. First this is done visually. The camshaft must be replaced if its working surfaces (cams and bearing journals) have:

• scratches;
• bullies;
• cut wear (for cams);
• enveloping a layer of aluminum from the “bed” (for support necks).

In addition, the camshaft must be replaced if even the slightest traces of deformation are found.

The degree of wear of the support journals and the supports themselves is determined using a micrometer and caliper. The table below shows the permissible diameters of the journals and working surfaces of the supports.

Defect detection is carried out using a micrometer and calipers

Table: permissible diameters of the camshaft journals and its “bed” supports for VZ 2107

If during the inspection it is determined that the dimensions of the working surfaces of the parts do not correspond to those given, the camshaft or “bed” must be replaced.

Timing shaft diagnostics

The camshaft, like any important component of an engine's design, affects its performance. Even minor defects in this device can negatively affect the engine power and its traction characteristics. This may also lead to unreasonably high gas mileage, and in the long run will lead to serious breakdowns requiring expensive repairs.

Next, we will discuss why a distribution valve is needed on the VAZ 2107, how to diagnose it and troubleshoot it yourself.

In the removed state, you can easily assess what defects are on the shaft. Visually, you can detect damage such as scuffs and scratches, as well as wear on the cut on the cams and coating of the aluminum word on the necks.

Even if minor traces of deformation were noticed, the camshaft on the VAZ 2107 must be replaced.

We present a table that shows the permissible values ​​of the dimensions of the shaft journals for its further use.

If these values ​​are not met, it is important to replace the “bed” or timing shaft.

Installing a new camshaft

In order to install a new timing shaft, you will need the same tools as to dismantle it. The installation procedure is as follows:

1. Be sure to lubricate the surfaces of the cams, bearing journals and bearings with engine oil.
2. We install the camshaft in the “bed”.
3. Using a 10 mm wrench, tighten the bolts of the thrust flange.
4. We check how the shaft rotates. It should turn easily around its axis.
5. We set the shaft to such a position that its pin would coincide with the hole on the fixing flange.
6. We install the bed on the studs, screw on the nuts, and tighten them. It is important to follow the established procedure. The tightening torque is in the range of 18.3–22.6 Nm.

   
   The nuts are tightened using a torque wrench with a torque of 18.3–22.6 Nm

7. We do not install the valve cover and camshaft sprocket in place, since it will still be necessary to set the valve timing.

Also check out

• Self-replacement of the VAZ 2110 CV joint
• How to replace the Lada Kalina fuel filter with your own hands. Installing a new fuel pump mesh
• How to replace the steering rack of a VAZ 2115 yourself

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

1. Using a key set to “13”, unscrew the nine nuts from the camshaft “bed”.

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

1. Remove the camshaft from the studs, dismantle it along with the “stock”.

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

1. Unscrew the mounting bolts of the thrust flange with a 10mm wrench and remove the flange.

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

1. Lift the cam, thereby releasing the spring pressure, and remove it.
2. Remove the camshaft from the “bed”.

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

1. Remove the cam spring.

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

Replacing the camshaft of VAZ 2107, VAZ 2106 with your own hands

Reassemble in reverse order. , the replacement of the camshaft of the VAZ 2107, VAZ 2106 can be considered complete

Note!

The camshaft stock mounting nuts should be tightened in strict accordance with the diagram below.

Setting ignition timing (valve timing) by marks

After the repair work has been carried out, it is necessary to set the correct ignition timing. To do this you need to do the following:

1. Install the camshaft sprocket with the chain, secure it with a bolt without tightening it.
2. Install the chain tensioner.
3. Place the chain over the crankshaft, accessory shaft and camshaft gears.
4. Using a 36mm wrench placed on the crankshaft pulley nut, rotate the crankshaft until the mark on the pulley aligns with the mark on the engine cover.

   
   Labels must match

5. Determine the position of the camshaft sprocket in relation to the “bed”. The mark on the star should also line up with the protrusion.

   
   If the marks do not match, you need to shift the sprocket relative to the chain

6. If the marks do not match, unscrew the camshaft sprocket bolt and remove it together with the chain.
7. Remove the chain and turn the sprocket to the left or right (depending on where the mark is shifted) by one tooth. Place the chain on the sprocket and install it on the camshaft, securing it with a bolt.
8. Check the position of the marks.
9. If necessary, repeat shifting the star by one tooth until the marks coincide.
10. Upon completion of work, secure the star with a bolt and the bolt with a washer.
11. Install the valve cover.
    Secure it with nuts. Tighten the nuts in the order shown in the photo. Tightening torque: 5.1–8.2 Nm. The nuts must be tightened with a torque wrench to a torque of 5.1–8.2 Nm
12. Carry out further engine assembly.

Check time alignment

If the crankshaft and camshaft marks do not match, the engine will not run correctly. Installing time stamps on a VAZ 2107 injector is no different from the same procedure on carburetor engines. The mark on the crankshaft pulley must match the mark on the front engine cover. And the point on the rim of the camshaft sprocket should be opposite the beacon on the bed.

Align the sign on the star with the ledge

When putting on the sprocket, block the camshaft so that it is stationary. Do not tighten the nut completely. Align the marks on the camshaft by turning the sprocket. The chain should remain in its original position, so throw links until you reach the alignment of the mark and casting on the bed. Then move the crankshaft with a wrench a quarter turn counterclockwise. Turn the crankshaft in the opposite position so that the marks on it match. When the marks are aligned on the crankshaft and camshaft, tighten the nut on the camshaft sprocket using a wrench. Tightening torque - 5 kgf. Adjust the chain tension using the tensioner.

READ Adjusting the front axle gearbox Niva Chevrolet