Installation of ventilated brake discs on a VAZ 2114

What is a brake disc and why is it needed?

The brake disc is an element of the front wheel braking mechanism. It is made of steel and has the shape of a plate, the rim of which serves as a working surface. The protruding part (bottom) of the disk is attached to the hub.

The pads are located in close proximity to the working surface of the part. When we press on the brake pedal, they press against the disc, causing it to slow down. This is how the front wheels of the “fourteenth” brake.

When disks need replacement

Replacing brake discs on a VAZ 2114 is not a routine type of work. Their service life, according to the manufacturer, is 100 thousand kilometers. This is provided that they are operated normally. But, as practice shows, they are enough for at most 70 thousand km, and only if the pads are changed on time.

Be that as it may, the driver needs to diagnose the condition of the discs at least once a quarter, and if excessive wear or damage is detected, take measures to replace them. Ignoring these recommendations can lead not only to the failure of other elements of the system, but also cause an emergency on the road.

VAZ 2114 brake discs must be replaced if:

• the thickness of at least one of them is less than 10.8 mm;
• there are grooves, chips, cracks on the working surface;
• the part is deformed due to mechanical damage.

pros

Let's look at why disc brakes are better than drum brakes:

1. Braking becomes more reliable, braking distance is reduced;
2. Braking forces are distributed more evenly, given that the VAZ 2114 is a front-wheel drive car;
3. There is an effect of faster response after pressing the pedal;
4. Unsprung masses are reduced;
5. Heat dissipation occurs better, which is especially important when driving on a mountain road or during active acceleration/braking. For this reason, the brake system is cooled better;
6. Disk ones are much easier to dismantle and replace;
7. There is no need to adjust the handbrake after each repair of the rear brakes, although this will have to be done the first time;
8. They do not freeze in winter after washing, like drum ones;
9. Rear disc brakes installed on the VAZ 2114 are much more convenient to control and promptly notice pad wear.

Which disks to choose

If replacing brake discs on a VAZ 2114 is inevitable, you should take care to select them correctly. Remember, your safety depends on their quality. And be prepared for the fact that you will have to buy not one disc, but a set of two pieces. Under no circumstances should you change them one by one! Due to uneven wear of parts, the braking efficiency of each wheel will be different. This may cause you to lose control of the vehicle.

The standard front brake disc for the VAZ 2114 (R-13) goes on sale under catalog number 2108-3501070. The price of the set, depending on the manufacturer and modification, can vary from 1100 to 4000 rubles.

Dismantling

Before installing disc brakes, you need to dismantle the old rear brake mechanisms of the VAZ 2114.

This is done like this:

1. Remove the wheel;
2. Remove the brake drum;
3. Remove the pads;
4. Remove the hub from the wheel, having first unscrewed the brake pipe.

You should prepare for the fact that dismantling will not be easy. Not only do the brakes have the unpleasant tendency to stick during operation, but the bolts are also “welded” by corrosion. Therefore, it is advisable to treat the nuts and bolts themselves with a special agent (for example WD 40) so as not to tear off their edges.

It is important to plug the removed pipe with something so that brake fluid does not leak out and air is not sucked into the system. After that - knock down the hub

This works best if you attach a board or lath to the back of the support disk and hit it with a hammer, moving the blows: one from below, the other from above. This will prevent you from causing serious damage to the disk.

Replacing brake discs VAZ 2114 - ventilated or conventional

Recently, ventilated wheels have become very popular among car tuning enthusiasts. Their main difference from conventional ones is the presence of holes and grooves (grooves) on the working surface of the parts. This design allows you to significantly reduce heating during intense braking. Such discs cost from 2500 rubles per set.

Is it worth installing them? If you are not a supporter of sporty driving and sharp braking, there is no need to overpay. Feel free to install standard parts. If you participate in racing or are simply used to aggressive driving, the best solution would be to install ventilated discs. Installing them, of course, is more hassle, but you will immediately feel the difference with regular ones.

Go to a service station or change it yourself

Replacing the front brake discs of a VAZ 2114 at a service station will cost you at least 2,500 rubles. From a financial point of view, this is not cheap. If you have experience with hand tools, you can do the replacement yourself. This procedure will take 4-5 hours, but the money will stay at home.

Replacing VAZ 2114 brake discs with your own hands involves using the following tools and means:

• jack;
• wheel wrench;
• key to 17;
• key for 12;
• mallet or hammer and wooden block;
• liquid VD-40;
• a piece of wire (30-50 cm).

Condition monitoring

In order to identify malfunctions in time and determine the wear of the pads, they require periodic preventive inspection.

Front brake

The estimated time for replacing the front brake pads is 15 thousand kilometers. But this period can be significantly reduced if:

• The quality of the roads on which the car is driven leaves much to be desired;
• The driver has an aggressive driving style;
• The roads are very busy, you have to press the brake pedal regularly;
• The quality of the previous pads is far from the highest, etc.

In practice, replacing the front pads on a VAZ 2114 is carried out more often than in the case of the rear ones. The fact is that the drums are installed at the rear, and the load on them is less than on the front disk devices. Plus, don’t forget that the VAZ 2114 is a front-wheel drive car.

Self-repair of VAZ 2114 - replacement of brake discs

The order of work is as follows:

1. We place the car on a flat horizontal platform. Turn on the parking brake. Support the rear wheels.
2. Using a wheel wrench, unscrew the wheel bolts of one of the front wheels.
3. We jack up the front part of the car body on the desired side. Unscrew the bolts completely. We remove the wheel.
4. Turn the steering wheel to the side until it stops so that you can reach the caliper mounting bolts.
5. Using a 17mm wrench, unscrew the bolts (2 pcs.) securing the caliper to the steering knuckle. We dismantle the brake mechanism assembly without disconnecting it from the brake hose. Using a piece of wire, we hang it, for example, on the shock absorber spring so that the brake hose does not twist.
6. We use VD-40 liquid to treat the places where the disc is connected to the hub, as well as the mounting pins. We wait 10-15 minutes for the liquid to “work”.
7. Using a 12mm wrench, unscrew the two pins securing the disk.
8. Remove the disc from the hub. If it does not come off, carefully knock it down using a mallet or a mallet with a wooden spacer. The blows must be applied from the back of the disc closer to its center.
9. When the disk is removed, clean the seat on the hub using a brush (dry rag). Additionally, you can treat it with VD-40 liquid.
10. We install the new disk in place. Screw in and tighten the guide pins.
11. We install the brake mechanism. We fix it with bolts.
12. We mount the wheel.
13. Remove the jack and tighten the wheel bolts.
14. Similarly, we change the brake disc on the other wheel.

Before driving onto the road, it is recommended to check the operation of the braking system off the road. To do this, drive at low speed somewhere in the yard and evaluate the effectiveness of braking.

Replacement

Today, many people prefer to install ventilated brake discs on the VAZ 2114. This is a largely justified decision, since a special system allows them to be additionally cooled by air flows. Relevant for fans of fast driving and sharp braking. These systems are effective and durable, so it won’t hurt to spend money on them.

As for the replacement procedure, the main task here is to dismantle the old disks. Installing new ones later won’t be too difficult. Just be sure to remember or even write down which unit was located where and in what position, so that, by analogy, you can then assemble the “constructor” in the reverse order.

The brake discs on each wheel are removed in the same way. Therefore, follow the instructions.

1. Place the car on as level a surface as possible, turn on the handbrake, and place supports under the wheels. This way you minimize the risk of the machine moving and causing injury to you.
2. Raise one of the wheels using a jack and begin removing it. We think you know perfectly well how wheels are removed on a VAZ 2114.
3. Next, loosen the brake cylinder a little.
4. Using a screwdriver, pry the boot off the upper guide of the brake pad.
5. Now you need to remove the caliper and pads. To remove the caliper, use a 17 mm wrench. Before unscrewing the caliper itself, be sure to remove the brake hose fastener.
6. Removal of the pads is carried out in a special way. We have prepared a separate special material for you about this.
7. To prevent brake fluid from leaking out of the system, place a container under the hose. Anything that leaks out can be poured back in after replacing the disks.
8. Proceed with a thorough cleaning of the work site. You will have to clean off all traces of dirt and remove rust on the brake surfaces. Just don't pick anything there. Use special highly effective washes.
9. When using chemicals, be sure to think about your own protection. Wear gloves and avoid contact with skin and eyes.
10. Treat all brake system components with the almighty WD40. Take special care under the hub bearings.
11. The wheel pins are removed using a 8mm wrench. Just make sure that during this operation the disk does not move from its current position.
12. Before removing the brake disc, lightly tap the surface of the unit. Just don't ram on the work surface.
13. Remove the disc.
14. Insert the new unit and proceed in the reverse order of dismantling.
15. All elements must be thoroughly lubricated beforehand, especially the hubs. Treat the working surface of the new brake disc with a special product. This will degrease the unit.
16. If the brake cylinders were replaced at the same time, bleeding the brake pedal will become a mandatory measure, without which it is strictly not recommended to operate the car.
17. In a similar way, change the second front brake disc on your VAZ 2114.

We recommend: How to replace the cabin filter of a UAZ Patriot with your own hands?

This procedure has its own difficulties. Therefore, get ready for the fact that you, as a beginner, will have to spend not 5, but 6-8 hours.

Features of replacing standard disks with ventilated ones

If you decide to install ventilated discs, you should know that all their modifications are wider than the standard ones. Therefore, in addition to them, you will need to buy appropriate calipers, front pad guides, as well as protective covers. Purchasing all these elements separately is quite problematic. It's better to buy a set. The standard kit for two wheels includes: discs, calipers, pad guides and faceplates (casings). The price for such a set starts from 9,000 rubles.

The algorithm for replacing standard disks with ventilated ones is a little more complicated and will take 5-6 hours. Here you need to disconnect the brake hoses and remove the brake cylinders. And after the work is completed, you will also have to bleed the brakes.

Installation Features

The replacement must be comprehensive, since ventilated discs will be installed in the brake mechanism, and they are wider than standard ones. In addition to new discs, you need to purchase the following parts:

• Caliper - a part from model 2110 or 2112 is suitable.
• Protective cover - this is not provided for standard brakes.
• Bracket and shoe guide - you can also take parts from a VAZ 2110 or 2112.

It’s also worth buying new R14 wheels in advance. There will be no defects after such tuning. On the contrary, the safety indicator will increase, since braking will be more effective. Drivers performing this type of upgrade are making changes to the brake system - this is prohibited and the text is provided for informational purposes only. Replacement can be done in the garage or outside - the main thing is that the parts are clean before installation and the surface is smooth. It is not necessary to buy domestic options. For example, many VAZ 2114 owners choose imported wheels, which are characterized by increased wear resistance and, of course, an increased price.